Aquatec 8800 Руководство по установке - Страница 2

Просмотреть онлайн или скачать pdf Руководство по установке для Водяной насос Aquatec 8800. Aquatec 8800 2 страницы. Pab8800 series ro booster pump

Печатать страницу

Read the OPERATIONAL AND INSTALLATION GUIDELINES carefully before starting to install the pump. Consult

the Factory if there is any question.

1. Determine the optimum location for your pump before proceeding.

Note: Locate the pump after the sediment pre-filter and before the carbon pre-filter (If part of R.O. system).

2. Turn off water.

3. Cut the 1/4" or 3/8" O.D. flexible tubing in sufficient length to avoid any stress on the tubing where it connects to the

pump or the fitting on any accessory.

4. Insert tubing into pump ports. If fittings are John Guest type, be sure tubing is inserted past the resistance point until it

bottoms out against the port stop. If the compression fittings with threaded nuts are used, insert tubing until it bottoms

out in the port and hand tighten the compression nut until the connection is tight. Then tighten the nut 1/2 turn

clockwise or follow the wrench tightening instructions provided by fitting manufacturer.

5. The "CDP" pump is now ready for operation. Open feed-water valve to allow water to flow through the R.O. system

(Open flow-restrictor by-pass valve if part of R.O. system).

6. If the power source is a transformer, plug the appropriate Aquatec supplied/approved transformer into the receptacle

and connect the pump to the transformer. If the power source is not a transformer, connect the pump to the

appropriate power source. Allow water to circulate, purging any entrapped air. For pumps equipped with our "AFT"

auto- flush, the flow restrictor by-pass will open and close automatically when the transformer is plugged in.

7. The pump will now start building pressure. Operating pressure will vary with membrane flow rate, flow restrictor flow

rate, feed-water pressure and line voltage. Check for fitting leaks.

Note: If the flow restictor is too small (We recommend 300Ml/min. for standard CDP 6800 series pumps and

500Ml/min. for CDP 8800 series pumps), or if the R.O. systems is clogged, an internal pump bypass mechanism limits

the output pressure.

8. If compression fittings with threaded nuts are used, observe any leaks after pump has run for approximately 15

minutes. Further tighten compression nuts approximately 1/8 to 1/4 of a turn on all fittings in the system. Wait 15

minutes and repeat the leak check.

Note: Further adjustments should not be necessary although it may take several days of operation before all air has

been purged and the system is stabilized.

SERVICING:

Every Year: Check system against operating standards.

Every 2-3 Years: Replace diaphragm and check against operating standards.

AQUATEC WARRANTY

Aquatec Water Systems, Inc. ("Aquatec") warrants its products to be free from defects in material an workmanship under

the following terms:

Series 58XX, 68XX, 88XX, 55XX, ERP 1000, ERP 500 as well as PFR/TLC and PAW: The warranty will last for a period

of thirteen months from date of shipping from an Aquatec warehouse with the exception that the period will be extended

for an additional twelve months for 68XX series, ERP 500 and ERP 1000. Aquatec's obligation under this warranty shall

be limited to replacing or repairing at Aquatec's discretion, any such product or part which is returned to Aquatec's

factory with a Return Material Authorization Number (RMA), transportation charges approved by Aquatec or prepaid, and

upon examination, is found to Aquatec's satisfaction to have been defective under the terms of this warranty. No credit

will be allowed against future purchases for items returned as defective under the terms of Aquatec's warranty.

This warranty does not extend to any products, which have been altered or modified outside the Aquatec

factory, nor does it apply to units that are returned in an unassembled condition. Furthermore, the warranty does

not extend to pumps that are identified by a 9XXX model number, indicating non-compliance with Aquatec's Engineering

Standards. This includes, but is not limited to, pumps ordered without an integral control mechanism. The warranty

guarantees that products will perform to Aquatec's flow and pressure specifications throughout the life of the warranty.

The warranty does not cover wear, appearance, misapplication or external water damage. If the returned product is

found not to be defective under the conditions of this warranty, a charge will be made for repair or replacement.

This is a Limited Warranty. It covers the product only and the extent of the coverage is limited to the cost of the

product. As the manufacturer has no control over shipping, handling and installation, the warranty cannot cover

water damage, or any other damage, caused by a leak or other malfunction.

This warranty is in lieu of all other warranties, expressed or implied, and no person is authorized to give any other

warranty or assume obligation or liability in Aquatec's behalf. Aquatec shall not be liable for any indirect, incidental or

consequential damages of any kind incurred by the reason of the use or sale of any defective product and part.