Aquatec ocean e-vip Manual de Instruções - Página 10

Procurar online ou descarregar pdf Manual de Instruções para Ajuda à mobilidade Aquatec ocean e-vip. Aquatec ocean e-vip 16 páginas.

Imprimir página
7.
Insert the screws into the armrest holder and
guide into the holes in the backrest frame.
8.
Replace the nuts in the fastening clamp if neces-
sary.
9.
Place the fastening clamp onto the backrest frame
so that the fixing of the fastening clamp engages
with the small hole.
10. Insert the screws into the nuts and tighten.
11. Guide the belt of the backrest cover around the
back rest frame, close it and then tighten all the
belts.
Follow the same procedure to adjust the armrests to
the lower position.
Important!
Open the belt below the armrest and feed it
through the backrest frame if you are adjusting
the armrest to the lower position.
6.3

Adjusting the backrest cover

Important!
●
To attach accessories or the chest belt, the
second belt lock can be opened from above
and the backrest cover can be passed by
the backrest frame on the inside at this
point (3, fig. 11).
●
At least three belts must always be passed
by the backrest frame (on the outside) and
their belt locks must be closed.
The backrest tension can be individually adjusted.
Tensioning:
Tighten the belts (1, fig. 11) of the backrest cover.
Loosening:
1.
Open the belt locks (2, fig. 11) by pressing the
lugs (arrows, fig. 11).
2.
Push the belt back through the lock.
3.
Close the belt locks.
4.
Slightly tension the belt.
6.4

Adjusting the position of the chest belt

Important!
●
The position of the chest belt must be ad-
justed to suit the user.
●
The position of both fastening clamps must
be adjusted by the same amount on both
sides.
●
The position of the right and left fastening
clamp is adjusted in the same way.
1.
At the backrest cover, open the belt lock of the
belt, which is guided along the inside of the back-
rest frame at the height of the chest belt.
EN
2.
On the backrest cover, open the belt lock of the
belt at the height where the chest belt is to be at-
tached.
3.
Feed this belt along the backrest frame and close
again.
4.
Use a star handle to unscrew the screw (1, fig. 7).
5.
Remove the chest belt (5, fig. 7).
6.
Remove both parts of the fastening clamp (2 and
4, fig. 7) and move it to the desired position.
7.
Place the inside part (4, fig. 7) of the fastening
clamp around the backrest frame.
8.
Push the outer part (2, fig. 7) of the fastening
clamp onto the internal thread (3, fig. 7) of the pin
on the inside part.
9.
Use the star handle to attach the chest belt to the
fastening clamp with a screw.
10. Guide the belt of the backrest cover around the
back rest frame, close it and then tighten all the
belts.
6.5

Adjusting the length of the chest belt

Important!
Adjust the length of the chest belt to fit the us-
er.
Use the belt lock on the chest belt to adjust chest belt
length. If the belt lock adjustment range does not allow
the proper adjustment, use the fastening clamps to ad-
just the length as follows:
1.
Use a star handle to unscrew the screw (1, fig. 7).
2.
Choose the chest belt length (5, fig. 7).
3.
Use the star handle to attach the chest belt to the
fastening clamp with a screw.
6.6

Adjusting the length of the heel loop

Important!
The velcro fastening for the heel loop should
always face backward.
1.
Open the velcro fastening at the heel loop (4,
fig. 5).
2.
Adjust the heel loop to the desired length.
3.
Close the velcro fastening again.
19