Aquatec ocean e-vip Manual de Instruções - Página 9

Procurar online ou descarregar pdf Manual de Instruções para Ajuda à mobilidade Aquatec ocean e-vip. Aquatec ocean e-vip 16 páginas.

Imprimir página
5.1.5

Mounting the seat plate

CAUTION!
Risk of catching
Do not reach between the seat surface and
the seat frame when pressing down the
seat plate.
1.
Place the seat plate (1, fig. 8) on the seat frame
(2, fig. 8) with the hole at the front.
2.
Push the seat plate as far back as it will go.
3.
Using the palm of your hand, push the sides of the
seat plate down, and then the front and the back,
until the seat plate snaps into the seat frame.
5.2

Recharging the battery

CAUTION!
There is a risk of injury from electric shock.
Only recharge the battery in dry rooms (not
in the bathroom).
Important!
●
Recharge the battery completely each time
before you use the bathlift.
●
Make sure that the voltage specifications
shown on the charger correspond to those
of the power mains.
●
The rechargeable battery can be charged if
the battery box is mounted or not.
1.
Pull off the cap (5, fig. 9) from the battery box
socket (1, fig. 9).
2.
Push the plug (6, fig. 9) for the charger (7, fig. 9)
all the way into the socket (4, fig. 9) on the battery
box.
3.
Insert the power plug (8, fig. 9) of the charger into
an approved power socket.
The recharge time lasts ca. 5 hours. During this time
period, the indicator lamp (4, fig. 12) on the hand con-
trol glows yellow. Afterwards, trickle charging (pulse
charging) takes place for ca. 3 hours. During this time
period, the indicator lamp on the hand control glows
green.
18
The charger control ends charging after approx.
eight hours. The indicator lamp on the hand control
goes out. This is to avoid "overloading" the battery.
4.
Pull the charger out of the power socket.
5.
Disconnect the charger plug from the battery box
socket.
6.
Seal the socket with the cap.
6

Operation

6.1

Adjusting the height of the footrests

1.
Pull up the footrest (1, fig. 5) slightly.
2.
Pull out the clip (8, fig. 5) and put it in again at the
required position. Pull out the footrest slightly fur-
ther if necessary.
3.
Push down the footrest until the groove (5, fig. 5)
catches the pin of the clip (8, fig. 5).
4.
Set the other footrest to the same height as de-
scribed.
6.2

Adjusting the height of the armrests

Important!
●
The height of the armrests must be adjust-
ed to suit the user.
●
The height of the armrests must be adjust-
ed by the same amount on both sides.
●
The height of the right and left armrest is
adjusted in the same way.
1.
At the backrest cover, open the belt lock of the
belt, which is guided along the inside of the back-
rest frame at the height of the armrests.
2.
Open the belt lock of the belt above the armrests
at the backrest cover (1, fig. 10).
3.
Feed this belt along the backrest frame and close
again.
Important!
The nuts are inserted loosely in the fastening
clamp and can fall out.
4.
Unscrew the screws (3, fig. 10) of the armrest
holder (4, fig. 10) using an Allen key (size 4).
5.
Remove the fastening clamp (2, fig. 10) with the
nuts from the inside of the backrest frame.
6.
Remove the armrest holder (4, fig. 10) with the
armrest and move upwards.
Important!
The small hole is for fixing the fastening clamp.
EN