Arcam DiVA A85 Manual - Página 6
Procurar online ou descarregar pdf Manual para Amplificador Arcam DiVA A85. Arcam DiVA A85 14 páginas.
Imprimir página
Using your A85 integrated amplifi er
9 bk
RECORD MODE
PHONES
PHONO/AUX
1
Front panel controls
This section describes how to operate your amplifi er.
If your amplifi er has not been installed for you, you should fi rst
read the section 'Installation: A85' on page 4.
POWER (and power indicator light)
Switches the unit on and off. (You can also switch the amplifi er
into standby mode with the remote control handset.)
The light indicates the status of the amplifi er. A red light means
the amplifi er is in standby mode (press the
button on the remote control, or the
panel, to switch between standby and powered-up modes).
When you switch your amplifi er on, the light glows amber
for a few seconds, during which time the speakers are
disconnected. The light changes to green when the amplifi er
is ready for use.
The light may fl ash if a fault has occurred – the fault type is
shown on the display. You should unplug the amplifi er and leave
it for a few minutes before reconnecting. If the fault cannot be
cleared, unplug your amplifi er and contact your Arcam dealer.
Source selectors
These buttons select the source connected to the
corresponding input. A light above the relevant button indicates
which input is currently selected and it will also usually be
shown on the display.
VCR
This input is similar to the other line level inputs on the amplifi er
and may be used with a VCR or a second recording unit (e.g.
cassette deck).
TONE
Switches the tone circuits on and off, including settings for
individual sources. Note that the tone LED does not light unless
a tone setting has been made. (see page 8).
Control knob, SELECT and ENTER
The control knob has two functions:
I
I
A85/P85
6
bl
bm
bnbo
ENTER
SELECT
CD
TUNER
AV
DVD
2
2
4
6
as a volume control, to adjust the output of loudspeakers
and headphones connected to the amplifi er, and of the
pre-amp output (
.
PRE OUT)
when used in conjunction with the
buttons, to customise amplifi er settings (see page 8).
3
8
Power/Standby
button on the front
POWER
3bobn
and
SELECT
ENTER
VCR
TAPE
TONE
SP1
4 5
6
Volume control settings
It is important to realise that the position of the volume
control is not an accurate indication of the power delivered to
your loudspeakers. The amplifi er often delivers its full power
long before the volume control reaches its maximum position,
particularly when listening to heavily recorded compact discs.
However the amplifi er also has to be capable of giving full
power output from much lower level sources, such as tuners
and cassette decks. Using these sources, the volume control
setting may be much higher before distortion (audible overload)
sets in. To compensate for this, the input levels of each source
may be individually adjusted to avoid accidental overload (see
page 8).
7
SP1 and SP2
These buttons allow you to select and deselect the main (
and secondary (
) set of speakers attached to your amplifi er.
SP2
The light above each button glows if the corresponding
speakers are currently selected. If both lights are out the
amplifi er will appear not to work, as all speakers are switched
off! If both are on, with two pairs of low impedance speakers
connected, overloads are more likely. Overloading the amplifi er
may cause it to shut down because of overheating.
1
PHONES
This socket accepts headphones with an impedance rating
between 8Ω and 2kΩ, fi tted with a 1/4-inch stereo jack plug.
If you wish to listen on headphones only, use the
buttons (if necessary) to mute the speakers. The headphone
socket is always active.
9
Remote control receiver
The remote control's infrared receiver is positioned to the left
of the
button. Ensure the receiver is in a clear line of
RECORD
sight from the remote control to allow signals to be received.
blbm
MODE, UP and DOWN
These buttons are mainly for use with future optional modules,
however the
and
buttons are used with the basic A85
UP
DOWN
amplifi er to move the cursor when customising the 'Welcome
message' (see page 8).
A85 INTEGRATED AMPLIFIER
SP2
POWER
7
8
)
SP1
and
SP1
SP2