Digiop Black BLK-IPE4101 Manual de instalação rápida

Procurar online ou descarregar pdf Manual de instalação rápida para Conversor de multimédia Digiop Black BLK-IPE4101. Digiop Black BLK-IPE4101 3 páginas. 4-channel h.264 network video encoder

Imprimir página

4-Channel H.264

Network Video Encoder

Quick Installation Guide

This document guides you through the basic steps to install and configure your DDIGIOP™ Black

BLK-IPE4101 4-channel IP encoder. For detailed instructions, refer to the User Manual.

Find the four MAC address on the product label and enter them here: __________________.

__________________. __________________. __________________.

Step 1.

Install the encoder

Mount the encoder in a secure location using the hardware installation kit provided. The kit includes

mounting brackets that slide into the sides of the encoder.

Connect video feeds from four analog cameras to the four Vin BNC connector (Vin1, Vin2, Vin3, Vin4) on the

front of the encoder.

Connections to the encoder for audio in and out (microphone and speaker), D/I sensor, alarm, video out

BNC, RS-232C, and RS-485 control are made through two 6-pin and two 8-pin terminal blocks. Vin1 is

associated with Ain1 (microphone), Aout1 (speaker), DI1 (sensor), DO1 (alarm output), and the first IP

channel. Similarily, Vin2 is associated with Ain2, Aout2, etc. Attach peripheral devices to the terminal

blocks as shown below. For detailed interface specifications, refer to the user manual.

Ain

1 - 4

Grounds

Aout

1 - 4

Grounds

Step 2.

Connect the encoder to the LAN

Attach a network LAN cable to the RJ-45 connector on the encoder backpanel.

Attach the DC12V adapter to the power connector on the encoder. DO NOT apply power to the encoder

at this time.

Step 3.

Install IPAdmin Tool

The IPAdminTool is a utility for configuring the network settings of your DIGIOP™ Black encoders and

installing new firmware. It can be loaded on a Microsoft® Windows® XP, Vista or Windows 7 operating

system. At a computer on the same LAN (subnet) where your encoder will be installed, do the following:

www.digiop.com

Ground

DI 1 - 4

RS-232 TX, RX, Gnd

DO 1 - 4

RS-485 +, –, Gnd

Common

Insert the CD disk provided with your encoder into your computer's CD ROM drive and open the CD in

a Windows Explorer window.

Find the IPAdminTool directory on the CD.

Copy the IPAdminTool directory with its contents to your computer hard drive.

Step 4.

Configure the network settings of you encoder

When your IP encoder is attached to a network and initially powered on, it attempts acquire compatible

network settings for each IP channel from a DHCP server. If it cannot find a DHCP server, it configures each

channel with the following static (fixed) settings:

IP address:

192.168.0.100

Subnet mask:

255.255.255.0

Gateway:

192.168.0.1

Your encoder must be configured with static network settings that are compatible with the LAN. If your

LAN has a DHCP server, use the following sub-step. Otherwise, use the sub-step procedure below for LANs

without DHCP.

Installing encoders on LANs with DHCP

Connect your encoder to the LAN, then plug in the power adapter to power it on.

Open the directory IPAdminTool directory on your computer, then double click the file

IPAdminTool.exe to start the application. When IPAdmin Tool starts, it will discover all the IP

devices it supports that exist on the network. The discovery process may take a few minutes.

Check the list of devices found by IPAdmin Tool. You can identify your encoder IP channels by their

MAC addresses.

The Rack Info field "M" number is directly associated with the Vin channel (M0 for Vin1, M1 for Vin2,

etc.). The Rack Info identifiers in the list may not appear in order. See the following table for the

example shown above.

Rack Info

Vin Channel

R0, B0, M0

Vin1

R0, B0, M1

Vin2

R0, B0, M2

Vin3

R0, B0, M3

Vin4

If an encoder channel was not found, click the Refresh button every minute until the four channels

for your encoder appear in the list.

Right click your encoder entry with Rack Info R0, B0,M0 (IP channel associated with Vin1), then

select IP Address from the drop-down list. An IP Setup window will open.

IP Address (via DHCP)

MAC Address

192.168.5.43:

00:13:23:D4:D1:45

192.168.5.59

00:13:23:D4:D1:46

192.168.5.61

00:13:23:D4:D1:47

192.168.5.50

00:13:23:D4:D1:48

Static Option

BLK-IPE4101_PQ

8/1/11