Sony MEX-N5000BT Manual de Instruções - Página 31
Procurar online ou descarregar pdf Manual de Instruções para Sistema estéreo Sony MEX-N5000BT. Sony MEX-N5000BT 40 páginas. Bluetooth audio system
Também para Sony MEX-N5000BT: Manual de Instruções (32 páginas), Instalação (2 páginas)
Imprimir página
Cautions
Be sure to install this unit in the dashboard of the
car as the rear side of the unit becomes hot during
use.
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in
moving parts (e.g. seat railing).
• Before making connections, turn the car ignition off
to avoid short circuits.
• Connect the yellow and red power supply leads
only after all other leads have been connected.
• Run all ground {earth} leads to a common ground
{earth} point.
• Be sure to insulate any loose unconnected leads
with electrical tape for safety.
• The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead {yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit's
rating must be higher than the sum of each
component's fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts list
([I])
• The numbers in the list are keyed to those in the
instructions.
• The bracket
CD
and the protection collar@) are
attached to the unit before shipping. Before
mounting the unit, use the release keys ®to
remove the bracket
CD
from the unit. For details, see
"Removing the protection collar and the bracket
(IEJ)"
on the reverse side of the sheet.
• Keep the release keys
®
for future use as they are
also necessary if you
~emove
the unit from your
car.
Caution
Handle the bracket
CD
carefully to avoid injuring your
fingers.
Connection example (IIJ)
Subwoofer Easy Connection {fA-C)
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
*1
MEX-GS610BT only
(f:J-A)
*2
not supplied
(f:J-B)
*
3
Do not connect a speaker in this connection
(f:J-C).
Notes
• Be sure to connect the ground (earth) lead before connecting the
amplifier
(f:J-A).
• The alarm will only sound if the built-in amplifier is used
(f:J-A).
• Be sure to connect a 4 - 8 ohm subwoofer. Do not connect a
speaker to the other rear speaker cord
(f:J-C).
Cannection diagram
(@}}
0
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
f)
To the power antenna {aerial} control lead or
power supply lead of antenna {aerial} booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in the
rear/side glass, see "Notes on the control and power supply
leads."
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a power antenna
(aerial). Connecting any other system may damage the unit.
E)
To a car's illumination signal
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
0
To the +12 V power terminal which is energized
in the accessory position of the ignition switch
Notes
• If there is no accessory position, connect to the +12 V power
{battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in the
rear/side glass, see "Notes on the control and power supply
leads."
0
To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.