Sony MEX-N5000BT Руководство по эксплуатации - Страница 31

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Стереосистема Sony MEX-N5000BT. Sony MEX-N5000BT 40 страниц. Bluetooth audio system
Также для Sony MEX-N5000BT: Руководство по эксплуатации (32 страниц), Установка (2 страниц)

Sony MEX-N5000BT Руководство по эксплуатации
Cautions
Be sure to install this unit in the dashboard of the
car as the rear side of the unit becomes hot during
use.
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in
moving parts (e.g. seat railing).
• Before making connections, turn the car ignition off
to avoid short circuits.
• Connect the yellow and red power supply leads
only after all other leads have been connected.
• Run all ground {earth} leads to a common ground
{earth} point.
• Be sure to insulate any loose unconnected leads
with electrical tape for safety.
• The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead {yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit's
rating must be higher than the sum of each
component's fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts list
([I])
• The numbers in the list are keyed to those in the
instructions.
• The bracket
CD
and the protection collar@) are
attached to the unit before shipping. Before
mounting the unit, use the release keys ®to
remove the bracket
CD
from the unit. For details, see
"Removing the protection collar and the bracket
(IEJ)"
on the reverse side of the sheet.
• Keep the release keys
®
for future use as they are
also necessary if you
~emove
the unit from your
car.
Caution
Handle the bracket
CD
carefully to avoid injuring your
fingers.
Connection example (IIJ)
Subwoofer Easy Connection {fA-C)
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
*1
MEX-GS610BT only
(f:J-A)
*2
not supplied
(f:J-B)
*
3
Do not connect a speaker in this connection
(f:J-C).
Notes
• Be sure to connect the ground (earth) lead before connecting the
amplifier
(f:J-A).
• The alarm will only sound if the built-in amplifier is used
(f:J-A).
• Be sure to connect a 4 - 8 ohm subwoofer. Do not connect a
speaker to the other rear speaker cord
(f:J-C).
Cannection diagram
(@}}
0
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
f)
To the power antenna {aerial} control lead or
power supply lead of antenna {aerial} booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in the
rear/side glass, see "Notes on the control and power supply
leads."
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a power antenna
(aerial). Connecting any other system may damage the unit.
E)
To a car's illumination signal
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
0
To the +12 V power terminal which is energized
in the accessory position of the ignition switch
Notes
• If there is no accessory position, connect to the +12 V power
{battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in the
rear/side glass, see "Notes on the control and power supply
leads."
0
To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.