Eckerle Gotec SP32/02-80-E Informações técnicas - Página 4

Procurar online ou descarregar pdf Informações técnicas para Bomba de água Eckerle Gotec SP32/02-80-E. Eckerle Gotec SP32/02-80-E 8 páginas. Oil lifters

Imprimir página

Technical Features

ELECTRICAL

TYPE

Voltage

Frequency

SP32

230 V

50 Hz

02-80

1. Description :

The SP32 02 suction pump incorporates an electromagnetic pump with

oscillating piston, a float (motor ignition and shutdown), a safety device

for overflowing, a thermal safety device, a low safety device, and a leak

detection float in the drip tray, all controlled by an electronic circuit.

The motor is protected by a fine filter that is built into a metal part.

Two additional electronic safety measures also protect the engine in

the event of the cistern being empty or leaking. The pump function is

secured by a drip tray and is delivered ready-made, with cable and pipe

fittings for ø 6/8 mm (ø 8/10 mm on request) copper tubes all included.

Maintenance is limited to a periodic cleaning of the suction filter.

Our pump conforms to standards regulations EN 12514.

2. Usage :

Suction pump SP32 02-80 is used as an intermediate tier in the feeding

of automatic oil burners. The pump sucks in the fuel oil until it reaches

a maximum level of 7m and fills its own tank with a capacity of 7.3 litres

per automatic cycle. There must not be a backflow preventer valve in the

suction pipe. With the tank being open, no purging system is required.

The oil burner can be above or below the pump (see examples). When

the burner is above the pump, the total height of the suction pipe in the

oil burner's cistern can reach 9m.

3. Caution during installation:

Before installing the pump, ensure the safety packaging is removed

as follows: remove the pump from the packaging, remove the lid by

loosening the 3 screws (10), take off the protective plastic caps on the

pipe fittings (15).

4. Wall Mounting

Accessibility between the lid and the pump must always be observed. It

must be located at least 30cm above the highest oil heater. Make sure

that this is straight (±2° tolerance). The pump must always be at least

30 cm above the highest level of the cistern. The oil lifter may only be

operated in dry and well-ventilated rooms

5. Pipe Installation

All the pipes (both suction and delivery) must be in ø 8/10 mm copper

tubes. If they are in ø6/8 mm tubes, replace the pump's ø 8/10 mm (15)

pipe fittings with ø6/8 mm pipe fittings, which are provided in the acces-

sories bag. Ensure the pipe fittings are airtight when assembled. The

pipe junctions are bit type sleeves. Avoid throttling and closed angles.

Do not use hemp to seal the pipe fittings. All this must be carried out in

accordance with legal regulations.

Order of Assembly

1. Assemble the packing boxes (14) without lock nuts on

the tubes (3 & 4).

2. Pass the tubes (3 & 4) through the purpose-made holes in the tank.

3. Assemble the packing box lock nuts (14) on the tubes (3 & 4)

as well as the nuts and bolts of the pipe fittings (15).

4. Connect the tubes (3 & 4) and tighten the pipe fittings (15).

5. Assemble the packing boxes (14) on the tank and then tighten all the

nuts

Power

Fuse

80 W

0,5 A

HYDRAULIC

Output function

for suction height

7 m

20 l/h

4 m

55 l/h

6. Electrical Installation

The power supply must be 230 V/50 Hz and grounded. The SP32 02

pumps are delivered with cable and power plug. A fast 0.5 A 20x5 fuse is

built into the electronic circuit.

Solenoid valve version

Do not forget to connect the solenoid valve to the oil burner before com-

missioning. This solenoid valve, which is normally closed, is controlled

by the oil burner. As soon as this stops, the solenoid valve's

power supply must be interrupted in order to avoid a possible siphonage

effect.

Key :

1. SP32 02-80 pump

3. Suction pipe

5. LCD Display

7. Power plug

9. Stove/Burner

11. Lid

mechanical anti-siphoning

14. Compression gland

ø8/10 mm or ø 6/8 mm

17. Fill opening

VERBRAUCHER :

Brenner über der

SP32-02

7. Using the SP32 02-80 pump

Use heating additive-free oil or kerosene. Check if the fuel oil in the cis-

tern is clean. Do not use additives, as those already incorporated are the

correct amounts to deal with improved combustion, ageing and resistan-

ce to the cold. Any further additions could quickly damage the pump.

Caution !

Upon ignition, a 10-minute delay prevents the pump from running

without liquid; the option of filling the suction pipe with a suction hand

pump must be considered if this pipe is long or part of a bigger section.

Start-up

1° Insert the plug (7) into the socket. When the display (5) shows 8. the

pump is powered.

2° Open the shut-off valve (8), and open the furnace valve

3° Press the switch (6), the LCD (5) will then show 0,1,2 and 3 in suc

cession.

- 4 -

MECHANICAL

Reseve-

Gewicht netto

Storage

7,3 l

7 Kg

2. Cistern

4. Feeding pipe

6. Switch

8. Shut-of valve

10. Screw of the lid

12. Electro-valve or

13. Lid of the cistern

15. Coupling

16. Drip tray

18. Float

VERBRAUCHER :

Brenner unter der

SP32-02