Toshiba TDP-WX5400U Manual do Proprietário - Página 19
Procurar online ou descarregar pdf Manual do Proprietário para Projetor Toshiba TDP-WX5400U. Toshiba TDP-WX5400U 42 páginas. Toshiba tdp-wx5400: user guide
Também para Toshiba TDP-WX5400U: Manual de instalação (16 páginas)
Imprimir página
Operations
Turning the power on and off
Connecting the power cord
Insert the power cord connector into
1
the AC IN socket of the projector.
2
Insert the power cord plug into a wall
or other power outlet.
Turning the power on
Remove the lens cap.
1
Remove the lens cap as shown (if present).
Be sure to remove the lens cap when the power is turned on.
If the cap is left on the projector, it could become deformed
due to heat.
Turn on the main power switch.
2
The ON/STANDBY indicator lights orange, and the
Status indicator lights green indicating standby mode.
3
Press the ON/STANDY button on
the control panel or on the remote
control.
The ON/STANDBY LED lights green and the internal
cooling fan starts.
4
After approximately 10 seconds,
the ON/STANDBY LED flashes
intermittently green.
The LAMP1 and LAMP2 LEDs light
5
green and the ON/STANDY LED
flashes more rapidly.
6
Once the ON/STANDBY, LAMP1 and LAMP2 LEDs are lit
solidly green, the projector is ready for use.
Power cord
connector
(supplied)
Remote
Control panel
control
ON/STANDBY STATUS
LAMP1
ON/STANDBY STATUS
LAMP1
ON/STANDBY STATUS
LAMP1
36
CAUTION
•
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyesight.
•
Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
•
Do not place your hands, face, or other objects near the air exhaust, the lamp cover or the bottom of
the unit. Doing so could result in injury and/or damage.
Notes
•
The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed.
•
When [Key lock] is [On], the operation buttons of the projector do not work
•
When [Password] is [On], enter password then the start-up screen is displayed after
the Password entry screen disappears
•
Do not touch the lens directly with your hand.
If fingerprints or stains are left on the projection lens surface, they may interfere with the
projector's ability to project images on the screen.
Turning the power off
Press the ON/STANDBY button on the control panel or the
1
remote control.
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.
The screen goes blank, but the internal cooling fan
continues to operate. Then, the projector goes into
standby mode.
During cooling, the ON/STANDBY indicator flashes. While the indicator is flashing, the
power can not be turned back on. However, there is no problem with unplugging the power
cord in this state.
Note
•
The projector consumes about 5W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
LAMP2
Precaution
•
If the power cord is unplugged before cooling is complete or the main power is turned
off, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp
LAMP2
overheats, it may fail to light.
Power saving mode
Power saving mode activates the standby condition consuming less power than
LAMP2
Standard mode. Go to the Setting-Setting 2 menu to turn on Power saving mode.
p.56
p.45
.
ON/STANDBY STATUS
LAMP1
.
LAMP2