Pioneer AVH-P6600DVD Manual de instalação - Página 4
Procurar online ou descarregar pdf Manual de instalação para Recetor Pioneer AVH-P6600DVD. Pioneer AVH-P6600DVD 9 páginas. 2004 mobile entertainment systems
Também para Pioneer AVH-P6600DVD: Manual do Proprietário (34 páginas), Manual do utilizador (24 páginas), Manual de operação (4 páginas)
Imprimir página
Installation
Note:
• When mounting the hide-away unit, make sure
none of the leads are trapped between the hide-
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected
away unit and the surrounding metalwork or fit-
up properly, and the unit and the system work
tings.
properly.
• Do not mount the hide-away unit near the heater
outlet, where it would be affected by heat, or near
• Use only the parts included with the unit to ensure
the doors, where rainwater might splash onto it.
proper installation. The use of unauthorized parts
can cause malfunctions.
• If the hide-away unit is installed in the passenger
• Consult with your nearest dealer if installation
compartment, anchor it securely so it does not
requires the drilling of holes or other modifications
break free while the car is moving, and cause
injury or an accident.
of the vehicle.
• If the hide-away unit is installed under a front seat,
• Install the unit where it does not get in the driver's
way and cannot injure the passenger if there is a
make sure it does not obstruct seat movement.
sudden stop, like an emergency stop.
Route all leads and cords carefully around the slid-
• Do not install the display where it may (i) obstruct
ing mechanism so they do not get caught or
pinched in the mechanism and cause a short cir-
the driver's vision, (ii) impair the performance of
cuit.
any of the vehicle's operating systems or safety
features, including air bags, hazard lamp buttons or
(iii) impair the driver's ability to safely operate the
Installing the remote control unit
vehicle.
• The semiconductor laser will be damaged if it
When not using the remote control unit,
overheats, so don't install the unit anywhere hot
secure it with velcro tape to prevent it
— for instance, near a heater outlet.
• If installation angle exceeds 30° from horizontal,
from moving.
the unit might not give its optimum performance.
• Thoroughly wipe off the surface
(Fig. 11)
before affixing the velcro tape.
Remote control
unit
Velcro tape (small)
(hard)
30°
Velcro tape (small)
(soft)
Fig. 11
• The cords must not cover up the area shown in the
figure below. This is necessary to allow the ampli-
fires to radiate freely. (Fig. 12)
Do not close this area.
Fig. 12
DIN Front/Rear-mount
This unit can be properly installed
either from "Front" (conventional DIN
Front-mount) or "Rear" (DIN Rear-
mount installation, utilizing threaded
screw holes at the sides of unit chassis).
For details, refer to the following illus-
trated installation methods.
Before installing the unit
Flush surface screw (5 × 6 mm)
• Remove the frame and the hold-
er. (Fig. 14)
Pull out to remove the frame and then
loosen the screws (2 × 3 mm) to
2. Install the unit into the dash-
remove the holder. (When reattaching
board. (Fig. 16)
the frame, point the side with a groove
After inserting the holder into the dash-
downwards and attach it.)
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
Holder
Dashboard
Screw (2 × 3 mm)
Frame
Fig. 14
53
DIN Front-mount
Holder
Fig.13
Installation with the rubber bush
1. Decide the position of the side
brackets. (Fig. 15)
When installing in a shallow space,
change the position of side brackets. In
this case, stick conceal tape on parts
• After installing the unit into the dash-
that protrude from the dashboard.
board, reattach the frame.
DIN Rear-mount
Installation using the screw holes on
the side of the unit
• Fastening the unit to the factory
radio mounting bracket. (Fig. 17)
Conceal tape
(Fig. 18) (Fig. 19)
Select a position where the screw holes
Side bracket
of the bracket and the screw holes of
this product become aligned (are fitted),
and tighten the screws at 2 places on
Fig. 15
each side. Use any of binding screws (4
× 3 mm), binding screws (5 × 6 mm) or
flush surface screws (5 × 6 mm),
depending on the shape of the screw
holes in the bracket.
*1 Use binding screws (4 × 3 mm) only.
* 1
* 1
182
Rubber bush
• When installing in a shallow space,
Screw
use the following screw holes. In this
case, stick conceal tape on parts that
protrude from the dashboard.
Conceal tape
Side bracket
* 1
Screw (2 × 3 mm)
* 1
Fig. 16
<ENGLISH>
Screw
Dashboard or
Console
Factory radio mounting
bracket
Fig. 19
Fixing the front panel
If you do not operate the removing and
attaching the front panel function, use
the supplied fixing screws to fix the
front panel to this unit.
• Fix the front panel to the unit
using fixing screws after remov-
ing the front panel. (Fig. 20)
Fixing screw
Fig. 17
Fixing screw
Fig. 20
Fig. 18