Pioneer AVH-P6600DVD Kurulum Kılavuzu - Sayfa 4

Alıcı Pioneer AVH-P6600DVD için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Pioneer AVH-P6600DVD 9 sayfaları. 2004 mobile entertainment systems
Ayrıca Pioneer AVH-P6600DVD için: Kullanıcı El Kitabı (34 sayfalar), Kullanıcı Kılavuzu (24 sayfalar), Kullanım Kılavuzu (4 sayfalar)

Sayfayı Yazdır

Installation

Note:

• When mounting the hide-away unit, make sure

none of the leads are trapped between the hide-

• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connected

away unit and the surrounding metalwork or fit-

up properly, and the unit and the system work

tings.

properly.

• Do not mount the hide-away unit near the heater

outlet, where it would be affected by heat, or near

• Use only the parts included with the unit to ensure

the doors, where rainwater might splash onto it.

proper installation. The use of unauthorized parts

can cause malfunctions.

• If the hide-away unit is installed in the passenger

• Consult with your nearest dealer if installation

compartment, anchor it securely so it does not

requires the drilling of holes or other modifications

break free while the car is moving, and cause

injury or an accident.

of the vehicle.

• If the hide-away unit is installed under a front seat,

• Install the unit where it does not get in the driver's

way and cannot injure the passenger if there is a

make sure it does not obstruct seat movement.

sudden stop, like an emergency stop.

Route all leads and cords carefully around the slid-

• Do not install the display where it may (i) obstruct

ing mechanism so they do not get caught or

pinched in the mechanism and cause a short cir-

the driver's vision, (ii) impair the performance of

cuit.

any of the vehicle's operating systems or safety

features, including air bags, hazard lamp buttons or

(iii) impair the driver's ability to safely operate the

Installing the remote control unit

vehicle.

• The semiconductor laser will be damaged if it

When not using the remote control unit,

overheats, so don't install the unit anywhere hot

secure it with velcro tape to prevent it

— for instance, near a heater outlet.

• If installation angle exceeds 30° from horizontal,

from moving.

the unit might not give its optimum performance.

• Thoroughly wipe off the surface

(Fig. 11)

before affixing the velcro tape.

Remote control

unit

Velcro tape (small)

(hard)

30°

Velcro tape (small)

(soft)

Fig. 11

• The cords must not cover up the area shown in the

figure below. This is necessary to allow the ampli-

fires to radiate freely. (Fig. 12)

Do not close this area.

Fig. 12

DIN Front/Rear-mount

This unit can be properly installed

either from "Front" (conventional DIN

Front-mount) or "Rear" (DIN Rear-

mount installation, utilizing threaded

screw holes at the sides of unit chassis).

For details, refer to the following illus-

trated installation methods.

Before installing the unit

Flush surface screw (5 × 6 mm)

• Remove the frame and the hold-

er. (Fig. 14)

Pull out to remove the frame and then

loosen the screws (2 × 3 mm) to

2. Install the unit into the dash-

remove the holder. (When reattaching

board. (Fig. 16)

the frame, point the side with a groove

After inserting the holder into the dash-

downwards and attach it.)

board, then select the appropriate tabs

according to the thickness of the dash-

board material and bend them.

(Install as firmly as possible using the

top and bottom tabs. To secure, bend

the tabs 90 degrees.)

Holder

Dashboard

Screw (2 × 3 mm)

Frame

Fig. 14

DIN Front-mount

Holder

Fig.13

Installation with the rubber bush

1. Decide the position of the side

brackets. (Fig. 15)

When installing in a shallow space,

change the position of side brackets. In

this case, stick conceal tape on parts

• After installing the unit into the dash-

that protrude from the dashboard.

board, reattach the frame.

DIN Rear-mount

Installation using the screw holes on

the side of the unit

• Fastening the unit to the factory

radio mounting bracket. (Fig. 17)

Conceal tape

(Fig. 18) (Fig. 19)

Select a position where the screw holes

Side bracket

of the bracket and the screw holes of

this product become aligned (are fitted),

and tighten the screws at 2 places on

Fig. 15

each side. Use any of binding screws (4

× 3 mm), binding screws (5 × 6 mm) or

flush surface screws (5 × 6 mm),

depending on the shape of the screw

holes in the bracket.

*1 Use binding screws (4 × 3 mm) only.

* 1

182

Rubber bush

• When installing in a shallow space,

Screw

use the following screw holes. In this

case, stick conceal tape on parts that

protrude from the dashboard.

Conceal tape

Side bracket

* 1

Screw (2 × 3 mm)

* 1

Fig. 16

Screw

Dashboard or

Console

Factory radio mounting

bracket

Fig. 19

Fixing the front panel

If you do not operate the removing and

attaching the front panel function, use

the supplied fixing screws to fix the

front panel to this unit.

• Fix the front panel to the unit

using fixing screws after remov-

ing the front panel. (Fig. 20)

Fixing screw

Fig. 17

Fixing screw

Fig. 20

Fig. 18