Pioneer AVH-P6600DVD Kurulum Kılavuzu

Alıcı Pioneer AVH-P6600DVD için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Pioneer AVH-P6600DVD 9 sayfaları. 2004 mobile entertainment systems
Ayrıca Pioneer AVH-P6600DVD için: Kullanıcı El Kitabı (34 sayfalar), Kullanıcı Kılavuzu (24 sayfalar), Kullanım Kılavuzu (4 sayfalar)

Sayfayı Yazdır

AVH-P6600DVD

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Printed in Japan

Imprimé au Japon

<CRD3858-A> UC

Connecting the Units

WARNING

CAUTION:

• To avoid the risk of accident and the potential vio-

lation of applicable laws, the front DVD or TV

• PIONEER does not recommend that you

(sold separately) feature should never be used

install or service your display yourself.

while the vehicle is being driven. Also, Rear

Installing or servicing the product may

Displays should not be in a location where it is a

expose you to risk of electric shock or

visible distraction to the driver.

other hazards. Refer all installation and

• In some countries or states the viewing of images

on a display inside a vehicle even by persons other

servicing of your display to authorized

than the driver may be illegal. Where such regula-

Pioneer service personnel.

tions apply, they must be obeyed and this unit's

• Secure all wiring with cable clamps or

DVD features should not be used.

electrical tape. Do not allow any bare

wiring to remain exposed.

• Do not drill a hole into the engine com-

partment to connect the yellow lead of

the unit to the vehicle battery. Engine

vibration may eventually cause the insu-

lation to fail at the point where the wire

passes from the passenger compartment

into the engine compartment. Take extra

care in securing the wire at this point.

• It is extremely dangerous to allow the

display lead to become wound around

the steering column or gearshift. Be sure

to install the display in such a way that it

will not obstruct driving.

• Make sure that wires will not interfere

with moving parts of the vehicle, such as

the gearshift, parking brake or seat slid-

ing mechanism.

• Do not shorten any leads. If you do, the

protection circuit may fail to work prop-

erly.

WARNING

LIGHT GREEN LEAD AT POWER CONNEC-

TOR IS DESIGNED TO DETECT PARKED

STATUS AND MUST BE CONNECTED TO

THE POWER SUPPLY SIDE OF THE PARK-

ING BRAKE SWITCH. IMPROPER CONNEC-

TION OR USE OF THIS LEAD MAY VIOLATE

APPLICABLE LAW AND MAY RESULT IN

SERIOUS INJURY OR DAMAGE.

ENGLISH>

Note:

• When an external power amp is being used with

• This unit is for vehicles with a 12-volt battery and

this system, be sure not to connect the blue/white

negative grounding. Before installing it in a recre-

lead to the amp's power terminal. Likewise, do not

ational vehicle, truck, or bus, check the battery

connect the blue/white lead to the power terminal

voltage.

of the auto-antenna. Such connection could cause

• To avoid shorts in the electrical system, be sure to

excessive current drain and malfunction.

disconnect the ≠ battery cable before beginning

• To avoid short-circuiting, cover the disconnected

lead with insulating tape. Especially, insulate the

installation.

unused speaker leads without fail. There is a possi-

• Refer to the owner's manual for details on

bility of short-circuiting if the leads are not insulat-

connecting the power amp and other units, then

make connections correctly.

ed.

• Secure the wiring with cable clamps or adhesive

• To prevent incorrect connection, the input side of

tape. To protect the wiring, wrap adhesive tape

the IP-BUS connector is blue, and the output side

around them where they lie against metal parts.

is black. Connect the connectors of the same

• Route and secure all wiring so it cannot touch any

colors correctly.

moving parts, such as the gear shift, handbrake and

• This unit cannot be installed in a vehicle that

does not have an ACC (accessory) position on

seat rails. Do not route wiring in places that get

the ignition switch. (Fig. 1)

hot, such as near the heater outlet. If the insulation

of the wiring melts or gets torn, there is a danger of

the wiring short-circuiting to the vehicle body.

• Don't pass the yellow lead through a hole into the

engine compartment to connect to the battery. This

will damage the lead insulation and cause a very

dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

ACC position

No ACC position

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on the fuse holder.

• The black lead is ground. Please ground this lead

• Since a unique BPTL circuit is employed, never

separately from the ground of high-current prod-

wire so the speaker leads are directly grounded or

ucts such as power amps.

the left and right ≠ speaker leads are common.

If you ground the products together and the ground

• If the RCA pin jack on the unit will not be used, do

becomes detached, there is a risk of damage to the

not remove the caps attached to the end of the con-

products or fire.

nector.

• Speakers connected to this unit must be high-

power types with minimum rating of 50 W and

impedance of 4 to 8 ohms. Connecting speakers

• Cords for this product and those for other products

with output and/or impedance values other than

may be different colors even if they have the same

those noted here may result in the speakers

function. When connecting this product to another

catching fire, emitting smoke or becoming dam-

product, refer to the supplied manuals of both

aged.

products and connect cords that have the same

• When this product's source is switched ON, a con-

function.

trol signal is output through the blue/white lead.

Connect to an external power amp's system remote

control or the car's Auto-antenna relay control ter-

minal (max. 300 mA 12 V DC). If the car features

a glass antenna, connect to the antenna booster

power supply terminal.

Fig. 1