Pioneer A-209R Manual de Instruções - Página 9

Procurar online ou descarregar pdf Manual de Instruções para Amplificador Pioneer A-209R. Pioneer A-209R 12 páginas. Stereo amplifier
Também para Pioneer A-209R: Manual de serviço (35 páginas), Manual de serviço (6 páginas)

Imprimir página

OPERATIONS

BEFORE BEGINNING OPERATIONS

1. Set the VOLUME control to minimum.

2. Set the POWER switch to ON.

3. Press the SPEAKERS button corresponding to

the speaker system to be used.

4. Set the BALANCE control to the center position.

5. Set the DIRECT button to off.

6. Set the TAPE2 MONITOR button to off.

PLAYBACK PROCEDURES

1. Set the INPUT SELECTOR knob to the desired

playback source.

÷ For playback of a compact disc: Set to [CD].

÷ For reception of an AM/FM broadcast: Set to [TUNER].

÷ For playback of a record: Set to [PHONO].

÷ For playback with the equipment connected to LINE

terminals: Set to [LINE].

÷ For playback of a tape: Set to [TAPE1/MD](on the A-

307R),TAPE1/CD-R/MD](on the A-209R).

NOTES:

÷ When you do not want to monitor the TAPE2 MONITOR

sound, set the TAPE2 MONITOR button to OFF.

÷ When you select PHONO, the sound is muted for a few

seconds.

2. Operate the equipment to begin playback.

3. Adjust playback volume with VOLUME control

on this unit.

4. Adjust the tone to your preference using the

BASS and TREBLE controls, and LOUDNESS but-

ton.

RECORDING TAPES

1. Select the recording equipment with the INPUT

SELECTOR knob.

2. Begin recording by operating the recording equip-

ment and cassette deck.

Refer to the operating instructions of your cassette deck

for proper operating procedures.

COPYING TAPES

When two decks are used, you can record the sounds from

one deck onto the other.

Application examples:

÷ To make a tape copy with contents identical to the original

tape.

÷ To edit a recording of an FM broadcast in order to cut out

unwanted commercials, recording only of desired material

onto another tape.

1. Load tapes for playback (pre-recorded tape) and

recording (blank tape) into the respective cas-

sette decks.

2. Select the copying direction with the INPUT SE-

LECTOR knob and TAPE2 MONITOR button.

÷ When copying from the cassette deck of TAPE1/MD(on

the A-307R) or TAPE1/CD-R/MD(on the A-209R) termi-

nals to the cassette deck of the TAPE2 MONITOR

terminals: Set the INPUT SELECTOR knob to TAPE1/

MD(on the A-307R),TAPE1/CD-R/MD(on the A-209R).

÷ When copying from the cassette deck of TAPE2 MONI-

TOR terminals to the cassette deck of TAPE1/MD(on

the A-307R),TAPE1/CD-R/MD(on the A-209R) termi-

nals: Set the TAPE2 MONITOR button to ON and the

INPUT SELECTOR knob to a position other than TAPE1/

MD(on the A-307R),TAPE1/CD-R/MD(on the A-209R).

3. Operate the cassette decks to begin copying.

Set the cassette deck with the original (playback) tape to

the playback mode, and set the cassette deck with the

blank tape to the recording mode.

TO USE THE COMPONENT CONNECTED

TO THE TAPE2 MONITOR TERMINALS

[For a cassette deck]

÷ A cassette deck connected here can be operated in the

same way (recording and playback) as a deck connected to

the TAPE2 MONITOR terminals.

÷ Also, if two decks are used, you can copy tapes from one

deck onto the other (see the section "COPYING TAPES").

1. Set the TAPE2 MONITOR button to ON.

2. Operate the cassette deck to perform playback

(or recording).

NOTE:

The source selected with the INPUT SELECTOR knob is

backed up for a few days even when the POWER switch is set

to off or the power cord is unpluged.

After this period, the CD is automatically selected when the

power is supplied.

[For an adaptor component]

By connecting a graphic equalizer, source sounds (from discs,

tapes, AM/FM broadcasts, etc.) can be heard with added sound

and tone compensation.

Sounds compensated with the adaptor component can be

recorded on the cassette deck connected to the TAPE1/MD(on

the A-307R) or TAPE1/CD-R/MD(on the A-209R) terminals.

1. Set the TAPE2 MONITOR button to ON.

2. Play back the source.

3. Operate the adaptor component.

NOTE:

Be sure to perform this operation with the adaptor component

power switch in the on position. Even when not using the

adaptor component, its power switch must be left on. If the

adaptor component is switched off, no sound will be pro-

duced, or the playback sound will be distorted.