Whirlpool Cabrio,- WED7300X Manual de utilização e cuidados - Página 13

Imprimir página

Whirlpool Cabrio,- WED7300X Manual de utilização e cuidados

5. Pour measured liquid fabric softener into the fabric softener

dispenser, if desired. Be sure to select the Fabric Softener

option to assure proper dispensing.

Do not overfill. The dispenser holds 4 oz (118 mL).

Concentrated fabric softener may be diluted with water

for a total of 4 oz (118 mL).

Do not spill or drip any fabric softener onto the clothes.

NOTES:

Use only liquid fabric softener in this dispenser.

Do not use fabric softener dispensing balls in this washer.

Dispensing balls will not operate correctly with this

washer.

6. Close the washer lid.

7. Press POWER. This turns on the washer display.

8. Select a Wash Cycle. See "Cycles."

9. Adjust the Modifiers, if desired. See "Modifiers."

10. Select desired Options. See "Options."

11. Select Delay Wash, if desired. See "Delay Wash" in the

"Modifiers" section.

12. Press START. The wash cycle begins, and the display shows

the estimated remaining time. The lid will lock.

NOTE: If you do not press Start within 5 minutes of pressing

Power, the washer automatically shuts off.

IMPORTANT: Water will be dispensed in the washer for a

moment, the lid will unlock, lock again, and then the cycle

will continue. This is normal.

Pausing or Restarting the Washer

Add a Garment

You can place additional clothing in the wash when the "Add a

Garment" status light is glowing without sacrificing wash

performance.

To add a garment or pause the washer at any time

1. Press PAUSE/CANCEL once.

2. Wait until the Lid Lock light turns off, then open the lid.

3. Add items.

To restart the washer

1. Close the lid and press START.

2. To pause the washer and unlock the lid at any time, press

PAUSE/CANCEL once. Pressing PAUSE/CANCEL twice will

cancel the wash cycle.

Stopping the Washer

You can stop the wash cycle and drain the tub by pressing the

Pause/Cancel button twice or the Power button once.

Changing Cycles, Modifiers and Options

You can change Cycles, Modifiers and Options anytime before

Start is pressed. Not all Modifiers and Options are available for all

cycles.

A short tone sounds when a change is selected.

Three short tones sound if an unavailable combination is

selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1. Press PAUSE/CANCEL twice to cancel the cycle. The washer

will drain.

2. Press POWER.

3. Select the desired wash cycle.

4. Select the desired Modifiers and Options.

5. Press START.

The washer restarts at the beginning of the new cycle.

NOTE: If you do not press Start within 5 minutes of pausing the

washer, the washer automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected

Modifier or Option begins by choosing the desired Modifiers and/

or Options.

NOTE: An error tone will sound if your selection is unavailable.

To manually drain the washer and spin the load

1. Press PAUSE/CANCEL twice to cancel the wash cycle and

drain the washer.

2. Press POWER.

3. Turn knob to select DRAIN & SPIN.

4. Press START.

When the spin is complete, the lid unlocks. Items can be

removed from the washer.

Status Lights

These lights show which portion of the cycle the washer is

operating. They also indicate when you can add other garments

to the wash load.

Load is Done

The Done light stays on until the lid is opened or the Power or

Pause/Cancel button is pressed.

Indicator lights

An indicator light shows which Cycle, Modifiers and Options you

have selected.

Estimated Time Remaining

When a wash cycle is started, the estimated time remaining for

the cycle, including fills and drains, will be displayed. The time

will count down to the end of the cycle.