Washer Maintenance
WATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of
replacement on the label with a permanent marker.
NOTE: This washer does not include inlet hoses.
See the Installation Instructions for more information.
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Efficiency (HE) detergents and follow the
HE detergent manufacturer's instructions regarding the
amount of HE detergent to use. Never use more than the
recommended amount because that may increase the
rate at which detergent and soil residue accumulate inside
your washer, which in turn may result in undesirable odor.
2. Use warm and hot wash water settings sometimes (not
exclusively cold water washes), because they do a better
job of controlling the rate at which soils and detergent
accumulate.
3. Always leave the washer lid open between uses to
help dry out the washer and prevent the buildup of
odor-causing residue.
Cleaning Your Top Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This
Washer Maintenance Procedure should be performed,
at a minimum, once per month or every 30 wash cycles,
whichever occurs sooner, to control the rate at which soils
and detergent may otherwise accumulate in your washer.
Cleaning the Inside of the Washer
To keep your washer odor-free, follow the usage instructions
provided above, and use this recommended monthly
cleaning procedure:
Clean Washer Cycle
This washer has a special cycle that uses higher water
volumes in combination with affresh
or liquid chlorine bleach to clean the inside of the washer.
Begin procedure
1. affresh
Washer Cleaner Cycle Procedure
®
(Recommended for Best Performance):
a. Open the washer lid and remove any clothing or items.
b. Place an affresh
Washer Cleaner tablet in the bottom
®
of the washer basket.
c. Do not place an affresh
in the detergent dispenser.
d. Do not add any detergent or other chemical to the
washer when following this procedure.
e. Close the washer lid.
f. Select the CLEAN WASHER cycle.
g. Touch and hold the START/PAUSE button for
3 seconds to begin the cycle. The Clean Washer
Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, touch POWER. After the Clean
Washer cycle has stopped, run a Rinse & Spin cycle to
rinse cleaner from washer.
12
Washer Cleaner
®
Washer Cleaner tablet
®
WASHER CARE (cont.)
2. Chlorine Bleach Procedure (Alternative):
a. Open the washer lid and remove any clothing
or items.
b. Add 1 cup (236 mL) of liquid chlorine bleach
to the bleach compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage
over time.
c. Close the washer lid.
d. Do not add any detergent or other chemical
to the washer when following this procedure.
e. Select the CLEAN WASHER cycle.
f. Touch and hold the START/PAUSE button for
3 seconds to begin the cycle. The Clean Washer
Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, touch POWER. After the Clean
Washer cycle has stopped, run a Rinse & Spin cycle to
rinse cleaner from washer.
Description of Clean Washer Cycle Operation:
1. This cycle will fill to a water level higher than in normal
wash cycles to provide rinsing at a level above the water
line for normal wash cycle.
2. During this cycle, there will be some agitation and
spinning to increase the removal of soils.
After this cycle is complete, leave the lid open to allow
for better ventilation and drying of the washer interior.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills.
Use only mild soaps or cleaners when cleaning external
washer surfaces.
IMPORTANT: To avoid damaging the washer's finish, do not
use abrasive products.
Imprimir página