Whirlpool WGD9450WR Manual de instruções de instalação - Página 4
Procurar online ou descarregar pdf Manual de instruções de instalação para Secador Whirlpool WGD9450WR. Whirlpool WGD9450WR 32 páginas. Gas/electric
Imprimir páginaINSTALLATION
REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Read
and follow the instructions provided with any tools listed here.
For All Installations:
•
Flat-blade screwdriver
•
Caulking gun and compound
(for installing new exhaust
•
#2 Phillips screwdriver
vent)
•
Adjustable wrench that
opens to 1" (25 mm) or
•
Tin snips (new vent
hex-head socket wrench
installations)
(for adjusting dryer feet)
•
1¼,nut driver
•
Level
(recommended)
•
Vent clamps
•
Tape measure
•
Pliers
Gas Installations:
•
8" or 10" pipewrench
•
Pipe-joint compound
resistant to LP gas
•
8" or 10" adjustable wrench
(for gas connections)
Parts supplied
Non-Steam Models
4 Leveling legs
Steam Models
A
B
E
C
D
A. Leveling legs (4)
B. "Y" connector
C. Short inlet hose
D. Inlet hose with right-angle
connector
E. Rubber washer
Remove parts package from dryer drum. Check that all parts
are included.
NOTE: Do not use leveling legs supplied with dryer if installing
on a pedestal.
Parts needed
Check local codes. Check existing electrical supply and venting.
See "Electrical Requirements" and "Venting Requirements" before
purchasing parts.
Mobile home installations require metal exhaust system hardware
available for purchase from the dealer from whom you purchased
your dryer. For further information, please refer to the "Assistance
or Service" section in your Use and Care Guide.
Optional Equipment
Refer to your Use and Care guide for information about the
accessories available for your dryer.
Location Requirements
Explosion Hazard
Keep flammable
materials
and vapors, such as
gasoline, away from dryer,
Place dryer at least 18 inches (460 ram) above the floor
for a garage installation,
Failure to do so can result in death, explosion,
or fire,
You will need
•
A location that allows for proper exhaust installation.
See "Venting Requirements."
•
Aseparate 30-amp circuit.
•
If you are using a power supply cord, a grounded electrical
outlet located within 2 ft (610 mm) of either side of the dryer.
See "Electrical Requirements."
•
A sturdy floor to support the total dryer weight of 200 Ibs
(90.7 kg). The combined weight of a companion appliance
should also be considered.
A level floor with a maximum slope of 1" (25 mm) under entire
dryer. If slope is greater than 1" (25 mm), install Extended Dryer
Feet Kit, Part Number 279810. Clothes may not tumble properly
and automatic sensor cycles may not operate correctly if dryer is
not level.
•
For a garage installation,you will need to place the dryer at least
18" (460 mm) above the floor. If using a pedestal, you will need
18" (460 mm) to the bottom of the dryer.
•
Steam models only: Cold water faucets located within
4 ft (1.2 m) of the dryer, and water pressure of 20-100 psi
(137.9-689.6 kPa). You may use the cold water supply from
your washer using the "Y" connector provided.
Do not operate your dryer at temperatures below 45°F (7°C). At
lower temperatures, the dryer might not shut off at the end of an
automatic sensor cycle. This can result in longer drying times.
The dryer must not be installed or stored in an area where it will be
exposed to water and/or weather.
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.
Installation
clearances
The location must be large enough to allow the dryer door to
open fully.
4