Whirlpool 24" Manual de instruções de instalação - Página 4

Procurar online ou descarregar pdf Manual de instruções de instalação para Campânula de ventilação Whirlpool 24". Whirlpool 24" 7 páginas. Convertible range hood

Imprimir página

terminal

. box

cover

Remove terminal box cover from

range hood.

Personal Injury Hazard

More than one person is required to help

with appliance

installation because of its

weight and size.

Failure to follow these instructions may

result in personal injury.

keyhole

slot

Lift the range hood into final

H position and center. Mark on the

underside of cabinet the location of the

four keyhole mounting slots. Set range hood

aside on a protected

surface.

i i

centerline

Determine and clearly mark a vertical

centerline on the wall and cabinet in the

area the vent opening will be made.

To wire through top, mark a line 7- l/2" from

the right of the centerline on the underside

of the cabinet. Mark the point on this line

that is l-3/8" from back wall. Drill a l-l /4"

diameter hole through the cabinet at this

point.

To wire through rear, mark a line 7-l /2" from

the right of the centerline on the wall. Mark

the point on this line that is 64-5/a" from the

floor (or l-3/8" from underside of cabinet).

Drill a l-1/4" diameter hole through wall at

this point.

Numbers

correspond

to steps.

To vent through the roof with 7" round

ductwork, mark 4- l/2" and 5" in from back

wall along the centerline on underside of

cabinet. Use these points as centers to

draw 7- l/8" circles on underside of cabinet.

Use a saber saw to cut the openings for the

ductwork. Repeat for the underside of the

top of the cabinet. This will create slotted

openings.

To vent through the roof with 3- l/4" x 10"

rectangular

ductwork, mark a line 1" and 5"

from the back wall on the underside of the

cabinet. Mark lines 5 l/4" to the right and

left of the centerline on the underside of

cabinet that connect the lines just drawn.

Use a saber saw to cut a rectangular

opening for the ductwork. Repeat for the

underside of the top of the cabinet.

To vent through wall with 3- l/4" x 10"

rectangular

ductwork, measure from floor

65-7/a" and 62-3/a" (or l/8" and 3-5/a" down

from underside of cabinet) and mark on

back wall. Measure and mark a line 5- l/4"

to right and left of centerline, connecting

the two lines. Use a saber saw to cut a

rectangular

opening for the ductwork.

ii.

Install ductwork through the vent opening in

upper cabinet or wall. Complete venting

system according

to method needed. See

"Venting requirements. II Use caulking to

seal exterior wall or roof opening.

Attach rectangular

damper to selected

rectangular

vent opening. If damper is

attached

to back of range hood, be sure

damper hinge is toward the top. For round

vented installations, use round damper in

duct to prevent air from flowing back into

ductwork. If roof cap has a damper,

remove damper blade from range hood.

13.

Run wiring through wall or cabinets

according

to the National Electrical Code

and local codes and ordinances.

Do Not

turn on power until installation is complete.

keyhole

slot

14.

screw

Start screws through neck of each of the

four keyhole mounting screw slots on range

hood.

15.

Lift range hood into final position, feeding

electrical wire through wiring opening. Align

keyhole mounting screws slots with marks on

underside of cabinet. Tighten mounting

screws to cabinet, making sure mounting

screws are in narrow neck of slot.

Panel C