ALCON Manor-2101 Manual de início rápido

Procurar online ou descarregar pdf Manual de início rápido para Sistemas de controlo ALCON Manor-2101. ALCON Manor-2101 2 páginas.

Imprimir página

Manor-2101

0–10 V-

Ballast or LED Driver Control

Compatible with any LED driver or ballast

that is compliant with IEC 60929 annex E

120 – 277 V ~ 50 / 60 Hz

Maximum Capacity

Load

0 – 10 V - Sink

8 A

30 mA

For use with 0 –10 V - Electronic

Fluorescent Dimming Ballasts or

LED Drivers

Package Contents and Parts Identiﬁcation

Control Wires

(Violet and Gray)

Control

Wallplate Adapter

Switching Wires

(Black)

Control-Mounting Screws

Adapter-Mounting Screws

Important Notes

Please Read Before Installation

•

Wallbox Dimensions: A single-gang wallbox (3 in high × 2 in wide ×

2½

individual controls.

•

Derating Instructions:

No derating required for multi-gang

installations.

•

Wiring Note: Always turn OFF power before installation. Install in

accordance with all national and local electrical codes.

•

Lamp Seasoning Requirements:

rescent lamp

manufacturers r

rescent lamps be operated

at full output (seasoned) before they can be dimmed, to render lamp

impurities inert, ensuring proper dimming performance and average

rated lamp life. Please contact your lamp manufacturer for seasoning

requirements.

•

Ballast/Driver Functionality Check:

With power OFF, check new

ballast for functionality prior to installation of control by connecting

the ballast's violet and gray wires together at the control. Turn power

on. The lights should now be at minimum brightness. With power OFF,

disconnect the wires. Turn power ON. The lights should now be at

maximum brightness.

•

Cleaning Instructions:

Clean dimmer with a soft damp cloth only.

Do not use any chemical cleaners.

•

Use this product only as intended with recommended accessories.

Control Unit

Front view

Wire Connectors

holes

Slider

Wallplate

Center-mounting holes

2845 S. Robertson Blvd. Los Angeles, CA 90034 USA

Pre-Installation

•

Determine if this will be a multi-gang installation or a single -gang installation.

•

If using a multi-gang installation, before proceeding to the Installation section, follow the Multi-gang Installation

procedure and refer to the instruction sheet supplied with multi-gang wallplates.

•

If using a single-gang installation, install control as outlined in the Installation section.

Multi-gang Installation

In multi-gang installations, several controls can be grouped horizontally in one ganging wallbox or in a series of

connected wallboxes. Multi -gang wallplates are available to simplify and improve the appearance of an installation.

For retroﬁt installations, the side sections can be removed to ﬁt existing wallboxes.

No Side Sections Removed

1. Determine the number of wallboxes necessary by

using the chart below. Use 3 in × 2 in (76 mm × 51 mm)

gangable wallboxes. Do not use plaster rings or gangbox

covers.

Number of Controls

Wallboxes

1 + 1

2. Install or modify appropriate wallboxes. For an EVEN

number of controls, wallboxes must be 3/4 in (19 mm)

apart to provide necessary space for the wallplate(s). For

example, when ganging four controls, three would be

in the four connected wallboxes and one would be in a

wallbox separated by the required space.

Four-gang

gangable

wallbox

3. When mounting controls, use center-mounting holes

Low-end

rol and o

-mounting holes for additional

trimpot

shaft

High-end

trimpot

shaft

(877)733-5236 | [email protected]

Side Sections Removed

Note: No derating required

1. One gangable wallbox is needed for each control

in the multi-ganged control. Individually connect

wallboxes or use a pre -assembled, multi-gang

wallbox.

2. Remove only inner side sections of control. Use pliers

4 + 1

7 + 1

to bend side sections down as far as you can then

back to their original positions. Side sections will

break o

Single-gang

Note: Do not remove outer side sections of the two

gangable

wallbox

controls that are on the ends of the gang.

3. When mounting, use center -mounting holes for

proper alignment.

3/4 in (19 mm)

(use chase nipple)

Multi-ganged

controls,

no side sections

removed

English

Multi-ganged

controls,

inner side

sections

(indicated

by shading)

removed