Directed Xpresskit DBALL2 Manual de instalação e referência rápida - Página 3

Procurar online ou descarregar pdf Manual de instalação e referência rápida para Por fechaduras Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 16 páginas. Ford5 remote start ready (rsr) installation
Também para Directed Xpresskit DBALL2: Manual de instalação (12 páginas), Manual de instalação (19 páginas), Manual de instalação (18 páginas), Manual (14 páginas), Manual de instalação (13 páginas), Manual de instalação (14 páginas), Manual de instalação (19 páginas), Manual de instalação (16 páginas), Manual de instalação (20 páginas), Manual de instalação (15 páginas), Manual de instalação (18 páginas), Manual de instalação (16 páginas), Manual de instalação (18 páginas), Manual de instalação (16 páginas), Manual (19 páginas)

Imprimir página
Directed Xpresskit DBALL2 Manual de instalação e referência rápida
Platform: DBALL2
Firmware: GM6

Installation Type 1 (with RFLCHGM)

This installation type does NOT support Immob. Bypass unless you use a RFLCHGM, which is sold separately.
Ignition Switch
Connector
Refer to the Vehicle
Key Side
Wiring Reference
Chart on page 9 for
wire color and location.
(+) Accessory:
(+) Ignition: Pink
Brown
Single Wire CAN:
RAP Off:
Refer to the
Vehicle Wiring
Reference Chart
on page 9.
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
(-) Hood Status Output: Blue/Red: 12
RFLCHGM
Note that the RFLCHGM component
is sold separately. Following RFLCHGM
instructions for programming procedure.
Not required in D2D mode.
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[1]
Trunk Release can be on TRUNK or on AUX1 depending on the vehicle, see Features & Option List section to change its operation.
[2]
Heated seat feature must be enable, see Features & Option List section.
[3]
Do not use GWR (Status) wire to activate heated seat feature. This wire needs to see a pulse after start for proper operation.
If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the central console for 10 minutes. Connect this wire
[4]
(Green/Black, pin 2/12) to the driver door sense trigger (Gray/Black) to avoid this issue. RAP Off: Refer to page 9 for wire color and location.
With the exception of the OBDII Diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).
(-) Ground
(+) 12V
(-) Parking Lights
Green, pin 1
1
8
9
16
Single Wire CAN: Light Green: 1
(+) 12V
(+) 12V: Brown: 7
(+) Ignition: Yellow: 8
(+) 12V
(+) 12V: Red: 13
(-) Ground: Black: 14
(-) Ground
(-) RAP Off: Green/Black: 2
[4]
(AC) Tach Output: Violet/White: 5
[1]
(+) Brake Status Output: Gray: 6
(+) Accessory Output: Gray/Black: 7
(-) Hood Status Input
(+) Brake Status Input
(AC) Tach Input
[1]
(-) Trunk Status Input
(-) Door Status Input
(-) Ground
(+) 12V
(-) Parking Lights
Diagnostic Connector OBDII
(connector side view)
RF
DBALL/
Prog. Button
DBALL2
LED
(-) Lock Output
(-) Unlock Output
(-) Trunk Release Output
(-) AUX1 Output
(-) AUX2 Output
[3]
(+) Starter Output
(+) Ignition Input/Output
(-) GWR (Status)
Diode
10: Blue/White: (-) GWR (Status) Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
5: Violet/Black: (-) AUX2 Heated Seat Input
4: White/Violet: (-) AUX1 Rear Hatch Input
3: Red/White: (-) Trunk Release/Tail Glass (if applicable) Input
2: Blue: (-) Unlock Input
1: Green: (-) Lock Input
(+)12V
RX
(-) Ground
TX
XKD2D65
© 2015 Directed. All rights reserved.
Rev.: 20151221
Page 3
[3]
[2]