ACORN AQUA A112408B/S-VR-UBL Instruções de instalação, operação e manutenção - Página 3

Procurar online ou descarregar pdf Instruções de instalação, operação e manutenção para Dispensador de água ACORN AQUA A112408B/S-VR-UBL. ACORN AQUA A112408B/S-VR-UBL 8 páginas. Vandal resistant refrigerated universal bi-level aquaaccess barrier free, wall mounted water cooler

Imprimir página

A112408S/B-VR VANDAL RESISTANT REFRIGERATED UNIVERSAL BI-LEVEL AQUAACCESS

(Alernate Configuration Left Unit Low with Right Unit High)

18 1 2 "

[470]

*20 7 8 "

[530]

TAILPIECE

GENERAL NOTES:

ALL DIMENSIONS ARE IN INCHES [MM]

ALLOW 4 INCHES [102 MM] MINIMUM CLEARANCE PER SIDE FOR VENTILATION

*3.

DIMENSIONS SHOWN ARE FOR RECOMMENDED ADULT HEIGHT. ADJUST VERTICAL

DIMENSIONS AS NECESSARY TO COMPLY WITH FEDERAL, STATE, & LOCAL CODES.

STOP VALVE, TRAP, & ELECTRICAL OUTLET NOT SUPPLIED.

IMPORTANT: COOLERS MUST BE ATTACHED TO WALL WITH ANCHOR SCREWS.

IMPORTANT:

1. Waste P-Trap, Water Supply Service Angle Stop Valve and 2" x 4" Electrical Plug-In Receptacle

to be supplied by others in accordance with local codes. A metallic p-trap (by others) must be

used for the drain connection.

2. Provide 4" minimum clear space on fixture sides to allow for proper ventilation through cabinet

louvers.

3. Water supply is 3/8" Outside Diameter copper tube. Waste is 1-1/4" Outside Diameter.

4. Completely flush supply lines of all foreign debris before connecting to fixture. Water cooler

designed to not affect taste, odor, color, or sediment. Optional water filter (Wf1) is available should

any of these problems arise from the water supply.

5. Do NOT solder copper tube when inserted into the coupler as damage to the o-ring will result.

6. All burrs must be removed from outside of cut tubes before inserting into coupler or other

components.

7. Power supply must be identical in voltage, cycle and phase to that specified on the cooler data

plate. Electrical outlet and furnished power cord with plug must be used to supply power to

fixture. Do NOT wire compressor directly to the power supply.

8. This unit must be grounded per the requirements of applicable electrical codes.

9. WARNING: Warranty is voided if installation is not made following current Acorn Aqua

installation instructions and if components are assembled to the fixture that is not approved by

Acorn Aqua.

10. Fixture operates within water pressure range of 20 to 105 psig. Acorn Aqua will not warranty

fixtures damaged when connected to supply lines with flow pressure lower than 20 psig or

higher than 105 psig. A pressure regulator must be furnished by others on supply line if inlet

pressure is greater than 105 psig.

11. Due to cold waste water, Acorn Aqua recommends that p-trap supplied by installer be insulated

to prevent excessive condensation.

12. Per UPC 609.10- All building water supply systems in which quick acting valves are installed

shall be provided with devices to absorb the hammer caused by high pressure resulting from the

quick closing of the valve. These pressure-absorbing devices shall be approved mechanical

devices. Water pressure-absorbing devices will be installed as close as possible to the quick

closing valve.

*38 3 4 "

*37 5 8 "

[984]

[956]

ORIFICE

RIM

HEIGHT

*32 3 4 "

[832]

*31 5 8 "

ORIFICE

HEIGHT

[803]

RIM

HEIGHT

Page 3 of 8

6 5 8 "

Ø 3 8 " [10]

[168]

3 HOLES

EACH

BRACKET

Ø 1 4 " [6]

4 ANCHOR

HOLES

*29 1 8 "

[740]

4 1 4 "

*15 5 8 "

[108]

[397]

7 7 8 "

[200]

Ø3/8" [10] O.D. COPPER TUBE SUPPLY

ELECTRICAL OUTLET

Ø1-1/4" [32] O.D. P-TRAP (NOT FURNISHED)

18 5 8 "

[473]

18 1 2 "

[470]

AIR FLOW

5 1 4 "

*27 7 8 "

[133]

*22 3 8 "

*21 5 8 "

[708]

6 1 2 "

[568]

[549]

[165]

*35 1 8 "

[892]