Nikon WR-R10 Manual do utilizador - Página 5

Procurar online ou descarregar pdf Manual do utilizador para Acessórios para câmaras Nikon WR-R10. Nikon WR-R10 6 páginas. Wireless remote controller/wr adapter
Também para Nikon WR-R10: Manual do utilizador (2 páginas), Manual do utilizador (2 páginas), Manual de início rápido (6 páginas), Manual (6 páginas)

Imprimir página

SURRiied Accessories

The product is sold in the sets below. This manual as-

sumes you have a WR-R1 0, WR-T1 0, and WR-A 10.

Case

Warranty

WR-R

Strap for WR-R1 0

Strap for WR-T1 0

~::A~h

CR2032 3

lithium battery'

User's Manual (this manual)

WR-R 1 0

Case

Warranty

Strap for WR-R1 0

User's Manual (this manual)

Strap for WR-T1 0

Warranty

WR-T10

CR2032 3 V lithium battery*

User's Manual (this manual)

WR-A10

User's Manual (this manual)

*Remove insulating sheet from WR-T10 before first use.

Parts of the Controller (Figure 1 ),

_ _ _ _ _ _

G) Red LED

®Channel selector

@Green LED

Pairing button

Strap eyelet

®Shutter-release button

Fn button

Strap eyelet

Red LED

@)Channel selector

Pairing button

~Hi~Jg

Release button

@Mounting mark

· · · · B

The WR-Rl 0 Strap

. Attach the WR-R1 0 to the camera strap as shown in

Figure 2 to prevent the WR-R1 0 being lost or dropped.

·····

· · · · B

Replacing CR2032 3 V Lithium Batteries {Figure 3)

·····

Replace the battery when the LED for the WR-T1 0 starts

· · · · to dim. Insert a fingernail behind the battery-chamber

latch and open the battery chamber (G)). Ensure that

· · · · · the battery is inserted in the correct orientation

(@)).

Using the WR-R1 0 (Transceiver),

_ _ _ _ _ _

Cameras with accessory terminals (Figure 4-a): Connect the

WR-R1 0 as shown by the marks on the camera (_.)

and WR-R1 0

('~).

Digital cameras with ten-pin remote terminals (Figure 4-b):

Attach the WR-A 10 WR adapter (G)) as shown by

the marks on the adapter (_.) and WR-R1 0

(T)

and

connect the assembly to the ten-pin remote terminal

(@),keeping the mounting mark on the WR-A 10 (G))

aligned with thee mark on the terminal. Tighten the

WR-A 1 0 locking screw

(@)).

Film cameras with ten-pin remote terminals (Figure 5): If the

terminal is on the front of the camera, remove the lens

or camera body cap (G)). Attach the WR-A 10, keep-

ing the mounting mark (G)) aligned with the mark on

the terminal (@). After tightening the WR-A 10 lock-

ing screw(@)), rotate the WR-A 10 (@)and attach the

WR-R1

(@)as shown by the marks on the adapter

(_.)and WR-R1 0 (T).

Note: Be sure the connectors are in the correct orienta-

tion; do not use force or insert the connectors at an an-

gle. Note that the WR-R1 0 can not be used with certain

accessories. Using force or inserting connectors at an

angle could damage the camera or accessory.

To remove the WR-R10, reverse the above steps. To re-

move the WR-A 10, press the release button (Figure

1-@) while sliding the adapter from the WR-R1 0.

The Fn Button

When a WR-R1 0 is mounted on the cameras below, the

· Fn button on the WR-T1 0 performs the function current-

ly assigned to the camera Fn button. See the camera

manual for details.

· 04

D800/800E

Using the WR-T1 0 (Transmitter),

_ _ _ _ _ _

The shutter-release button on the WR-T1 0 performs

the same functions as the camera shutter-release

button whether pressed halfway or all the way down.

See the camera manual for details.

Channel Selection and Pairing

If the camera fails to respond to the shutter-release but-

ton on the WR-T1 0, re-establish the link between the

WR-T1 0 and the receiver by matching channels and

pairing the devices as described below.

Set the units to the same channel.

Set the channel selectors on

both units to the same channel

(5, 1 0, or 15). Devices on differ-

ent channels can not be paired,

while paired devices can only

be used together when both

are set to the same channel.

Pair the devices.

After turning the camera on,

place the two devices close

together and press the pairing

buttons on both units simultane-

ously. Keep the buttons pressed

until the red and green LEOs on the WR-R1 0 flash on

and off in sequence, indicating that pairing is complete.

To erase pairing data, turn the camera on and keep the

WR-R1 0 pairing button pressed for about 3 seconds until

the green LED flashes rapidly, and then quickly press the

pairing button twice before the green LED stops flash-

ing. The green and red LEOs will both flash twice simul-

taneously to show that all pairing data has been erased.