Acoustic Energy AEG05/P5 Manual do Proprietário - Página 14
Procurar online ou descarregar pdf Manual do Proprietário para Altifalantes Acoustic Energy AEG05/P5. Acoustic Energy AEG05/P5 16 páginas. Powered 5.1 surround sound speaker system
Imprimir página
AEGOp5 Operation
- Pro Logic Mode
Pro Logic Mode
Your AEGO
5 will automatically switch to
P
Pro Logic mode when it detects a Pro Logic
signal. With other types of input signal, you
can select the Dolby Pro Logic mode
manually by pressing Pro Logic button on
the remote. Repeatedly pressing the
Pro Logic Button will switch the Pro Logic
mode in between the following modes;
AUTO, ALL PCM, ENABLE and DISABLE.
If a Pro Logic signal is detected, AEGO
mode automatically, and the display shows the following information:
DOLBY DIGITAL CO
PROLOGIC AUTO
If a stereo signal (either analog or digital) is detected, AEGO
switch to stereo mode automatically. You can then convert the stereo
mode to Pro Logic mode by pressing the Prologic button until you see
the following on the display:
DOLBY DIGITAL CO
PROLOGIC ALL PCM
DOLBY DIGITAL CO
PROLOGIC ENABLE
If you want to convert Pro Logic or 2-channel Dolby Digital signal into
Stereo mode, you can press the Prologic button until you see the
following on the display:
DOLBY DIGITAL CO
PROLOGIC DISABLE
AEGOp5 Operation - Speaker
Mode with Bass Manager
Speaker Mode with Bass Manager
The six LEDs on front panel of your AEGO
represent the six discrete audio channels
(Left, Right, Centre, Rear Left, Rear Right
and Sub). If a particular channel is active,
the LED will light up in green. The LED will
be red if that particular channel carries
bass signal below 120Hz.
Speaker Mode
Pressing the CEN button, switches the
centre channel on and off. The LCD will
display the following:
DOLBY DIGITAL CO
SPK C
ON
DOLBY DIGITAL CO
SPK C
OFF
AEGOp5 Operation
input
power
mute
test
balance
delay
prologic
field
EQ on/off
EQ setup
preset 1
preset 2
preset 3
save1
preset 4
load
BassManager
Cen
SL/SR
SW
VOL
D Ti
5 will switch to Pro Logic
P
5 will
P
field
EQ on/off EQ setup
5
P
preset 1
preset 2
preset 3
save1
preset 4
load
BassManager
Cen
SL/SR
SW
VOL
D Time
DRC
reset
Pressing the SL or SR button, switches the surround
channels on and off. The LCD will display the following:
DOLBY DIGITAL CO
SPK SUR
ON
DOLBY DIGITAL CO
SPK SUR
OFF
Pressing the SW button, switches the subwoofer on and off.
The LCD will display the following:
DOLBY DIGITAL CO
SPK SW
ON
DOLBY DIGITAL CO
SPK SW
OFF
Bass Manager
Pressing the BASS MANAGER button enables you to select from
three different settings of Bass; Bass Config.1, Bass Config.2 and
Bass Config.3. These selections will feed the bass signal
below 120Hz to different speakers as described below.
Bass Config.1
With this setting, the bass signal below 120Hz will be sent to the
subwoofer; the LEDs on the front panel indicating SW will be red,
and the LCD will show the following:
DOLBY DIGITAL CO
BASS CONFIG.1
Bass Config.2
With this setting, the bass signal below 120Hz will be sent to front left
and right speakers and the subwoofer; the LEDs on the front panel
indicating L/R/SW will be red, and the LCD will show the following
information:
DOLBY DIGITAL CO
BASS CONFIG.2
Bass Config.3
With this setting, the bass signal below 120Hz will be sent to all the
speakers; the LEDs on the front panel indicating L/R/SL/SR/SW
channels will be red and the LCD will show the following information:
DOLBY DIGITAL CO
BASS CONFIG.3
Bass Config. Off
With this setting, the bass signal below 120Hz will be sent to all
the speakers; the LEDs on front panel of AEGOP5 indicating
L/R/C/SL/SR/SW channels will be red and the LCD will show the
following information:.
DOLBY DIGITAL CO
BASS CONFIG.OFF
13