esera automation 11124 Manual do utilizador - Página 2

Procurar online ou descarregar pdf Manual do utilizador para Adaptador esera automation 11124. esera automation 11124 3 páginas. For 1-wire cable temperature sensors

Imprimir página
4
Assignment RJ45 socket
The RJ45 socket is compliant with the recommendations of www.1-Wire.org,
ESERA and IP-Symcon occupied.
The standard for the RJ45 pin assignment is based on a standardization
Proposal of "1.Wire.org", which can be found here.
us/p_2.html. The following assignment is an extension of the above standard and
does not conflict with it. Numbering of the socket, view from outside into the socket
(from plug side)
1
1-Wire
GND
Bus
5
Assignment screw terminal (1-Wire network)
Screw terminals +5V, +12V, Data (1-Wire) and GND are provided for connection to the 1-Wire network. The
assignment is printed on the printed circuit board.
6
Operating conditions
The module may only be operated at the specified voltages and ambient conditions. The device can be operated
in any position. The device is intended for use in dry and dust-free rooms.
If condensation is formed, allow up to 2 hours for the unit to acclimatize.
Assemblies and components should not be handled by children!
The modules may only be put into operation under the supervision of a qualified electrician.
The accident prevention regulations of the
Verband der gewerblichen Berufsgenossenschaften für elektrische Anlagen und Betriebsmittel
must be observed in commercial facilities.
Do not operate the module in an environment in which flammable gases, vapours or dusts are present or may be
present.
7
Assembly
The installation site must be protected from moisture. The device may only be used in dry indoor rooms and in
protected outdoor areas. The printed circuit board is open and not electrically insulated, therefore insulated
mounting to metal surfaces and other electrical cables must be provided.
The device is intended for installation inside a control cabinet as a stationary device.
8
Disposal instructions
Do not dispose of the device in domestic waste! Electronic devices are to be disposed of
according to the Directive on waste electrical and electronic equipment (WEEE) on local
authorities and collection points for waste electronic equipment!
9
Safety instructions
When using products that come into contact with electrical voltage, the valid VDE regulations must be
observed, especially VDE 0100, VDE 0550/0551, VDE 0700, VDE 0711 and VDE 0860
All final or wiring work must be carried out with the power turned off.
Before opening the device, always unplug or make sure that the unit is disconnected from the mains.
Components, modules or devices may only be put into service if they are mounted in a contact proof housing.
During installation they must not have power applied.
Tools may only be used on devices, components or assemblies when it is certain that the devices are disconnected
from the power supply and electrical charges stored in the components inside the device have been discharged.
Live cables or wires to which the device or an assembly is connected, must always be tested for insulation faults or
breaks.
If an error is detected in the supply line, the device must be immediately taken out of operation until the faulty cable
has been replaced.
When using components or modules it is absolutely necessary to comply with the requirements set out in the
accompanying description specifications for electrical quantities.
If the available description is not clear to the non-commercial end-user what the applicable electrical characteristics
for a part or assembly are, how to connect an external circuit, which external components or additional devices can
be connected or which values these external components may have, a qualified electrician must be consulted.
All rights reserved. Reproduction as well as electronic duplication of this user guide, complete or in part, requires the written consent of
ESERA GmbH. Errors and technical modification subject to change. ESERA GmbH, ESERA-Automation 2020
www.esera.de
2
3
5V,
GND
max. 50mA
11124 V1.0 R1.1 Manual
http://www.1wire.org/en-
4
5
1-Wire Data
GND
Primär
6
7
1-Wire Data
+12V,
Sekundär
max.
200mA
Page 2 of 3
8
GND