Blue Angel BSPF Manual de instruções e de peças - Página 2

Procurar online ou descarregar pdf Manual de instruções e de peças para Bomba de água Blue Angel BSPF. Blue Angel BSPF 4 páginas. Submersible sump pump

Imprimir página

Operating Instructions and Parts Manual

Installation

(continued)

Grounded

Check

Outlet

Valve

Inlet Pipe

14 in.

Figure 1

Dia.Min.

Flood risk. If

ﬂ exible discharge

hose is used, make sure pump is secured

in sump pit to prevent movement.

Failure to secure pump could allow pump

movement and switch interference and

prevent pump from starting or stopping.

3. A check valve is required in the

discharge line to prevent back-flow

when the pump shuts off. It is best

to install the check-valve directly to

the pump discharge. Thread a check

valve into the pump discharge.

4. Connect 1-1/4 in. or 1-1/2 in. rigid

pipe to rubber boot on check valve.

(Reverse boot for 1-1/2 in. diameter

pipe.) Tighten hose clamps.

Support pump and

piping when

assembling and after installation.

Failure to do so could cause piping to

break, pump to fail, etc. which could

result in property damage and/or

personal injury.

Make sure there is

adequate room for

the ﬂ oat switch to move freely during

operation (see Figure 2).

Place pump

where the

ﬂ oat will

not be

obstructed

A freely

moving ﬂ oat

ensures that

the pump will

perform properly.

NOTICE: An obstructed ﬂ oat will

cause the pump to fail.

Figure 2: Freely moving ﬂ oat switch

www.blueangelpumps.com

5. Protect electrical cord from sharp

objects, hot surfaces, oil and

chemicals. Avoid kinking the cord and

replace damaged cords immediately.

6. A sump pit cover must be installed

to prevent debris from clogging or

damaging the pump.

Operation

24 in.

Min.

disconnect the power source

before attempting to install,

service, relocate or maintain

the pump. Never touch sump pump,

Inlet

pump motor, water or discharge piping

Screen

when pump is connected to electrical

power. Never handle a pump or pump

motor with wet hands or when standing

on wet or damp surface or in water.

Fatal electrical shock could occur.

1. A ground fault circuit interrupter

(GFCI) is required.

is supplied with a grounding conductor

and grounding type attachment plug.

Use a grounded receptacle to reduce the

risk of fatal electrical shock.

Never cut off the round grounding

prong. Cutting the cord or plug will

void the warranty and make the pump

inoperable.

2. This pump is only for use on 120 Volt

(single-phase), 60 hz, 15 amp service

and is equipped with a 3-conductor

cord and 3-prong, grounding type plug.

DO NOT USE AN EXTENSION CORD.

3. Insert the pump power cord plug

directly into a GFCI protected 120

Volt outlet (See Fig. 3).

Power

Figure 3

4. Fill sump with water. The pump

will start automatically when the

water has filled the sump to a depth

of approximately 9 in. The pump

will stop when the water depth is

approximately 4 in. The pump will

recycle thereafter as required.

Always

Risk of electrical

shock! This pump

Grounded

Grounding

Outlet

Blade

TEST

RESET

Cord

BCS, BSPF, and SSBCS Series

Do not operate the

pump unless it

is submerged in water. Dry running

causes pump failure.

5. While the pump is draining the pit,

verify that the discharge piping is

carrying the water to a point several

feet away from the foundation.

6. If pump discharge line is exposed

to freezing temperature, the

exposed line must be pitched to

drain. Trapped water will freeze and

damage the pump.

NOTE: The motor is equipped with an

automatic reset thermal protector.

Maintenance

Always

disconnect the electrical

supply before attempting to

install, service, relocate or

perform any maintenance. If the power

source is out of sight, lock and tag

in the open (off) position to prevent

unexpected power application. Failure

to do so could result in fatal electrical

shock. Only qualiﬁ ed electricians should

repair this unit. Improper repair could

result in fatal electrical shock.

1. Let the pump cool for a minimum of

two hours before servicing because

the pump contains hot oil under

pressure and the motor is hot.

2. Disassembly of the motor prior to

expiration of warranty will void the

warranty. If repairs are required, see

troubleshooting chart.

3. Inlet should be kept clean and free

of all foreign objects and inspected

annually. A clogged inlet will

damage pump.

4. Pump should be checked monthly

for proper operation. Check pump

by following step 4 listed in the

operation section.

This pump contains

dielectric oil for

cooling. This oil can be harmful to

the environment. Check the state

environmental laws before disposing

this oil.