Cole Parmer Electrothermal MC5X1 Руководство по эксплуатации - Страница 17
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Контроллер Cole Parmer Electrothermal MC5X1. Cole Parmer Electrothermal MC5X1 20 страниц. Heating controller
Печатать страницу
9.5.11. Reconnect the mains and neutral wires from the cable to the PCB. (See wire
9.5.11. Reconnect the mains and neutral wires from the cable to the PCB. (See wire diagram).
diagram).
9.3. Servicing.
This product should be serviced by a Bibby Scientific Service Engineer or by an agent
on behalf of Bibby Scientific l. If in doubt contact Bibby Scientific. See Section 10.
9.4. Calibration
9.4.1.
Recalibration
• Have a precision reference thermometer of calibrator to hand. Ensure that
OS1=0 and SIM=0
• Switch the controller off and on again.
• During the auto-test phase, press buttons button's
keep them pressed until the controlled shows 0AD.
9.5.12. Replace the base and refit the two securing screws.
• With buttons
9.5.12. Replace the base and refit the two securing screws.
calibration of 0, inserting a constant corrective over the while scale of
The responsible body shall check the electrical safety of the unit before further use.
measurement. SAD allows a calibration of the top part of the measurement
The responsible body shall check the electrical safety of the unit before further
scale with a proportional correction between the calibration point and 0
use.
9.6. Spillage and Decontamination.
• Press
In the event of spillage switch off and unplug this product from the mains electrical supply.
reference instrument.
Wipe off all excess liquid from the product and surrounding area using an absorbent soft cloth.
9.6.
Spillage and Decontamination.
Allow sufficient time for any ingress of liquid to evaporate before commencing with use.
• Exit from calibration by pressing button
In the event of spillage switch off and unplug this product from the mains electrical
If in doubt please consult Customer Support. Refer to section 10.
supply. Wipe off all excess liquid from the unit and surrounding area using an
9.5. Spillage and Decontamination.
absorbent soft cloth.
In the event of spillage switch off and unplug this product from the mains electrical
supply. Wipe off all excess liquid from the unit and surrounding area using an
If in doubt please consult Customer Support. Refer to section 11.
absorbent soft cloth.
is responsible for carrying out appropriate decontamination. If hazardous material has
been spilt on or inside the equipment, decontamination should only be undertaken
If in doubt please consult Customer Support. Refer to section 10.
If the equipment has been exposed to contamination, the
under the control of the Responsible Body with due recognition of possible hazards.
Responsible Body is responsible for carrying out appropriate
Before using any cleaning or decontamination method, the Responsible Body should
check with the manufacturer the proposed method will not damage the equipment.
decontamination. If hazardous material has been spilt on or inside
If the equipment has been exposed to contamination, the
the equipment, decontamination should only be undertaken under the control
Responsible Body is responsible for carrying out appropriate
Prior to further use, the Responsible Body shall check the electrical safety of the unit.
decontamination. If hazardous material has been spilt on or inside the
of the Responsible Body with due recognition of possible hazards. Before
Only if all safety requirements are met can the unit be used again. The above
equipment, decontamination should only be undertaken under the control of
using any cleaning or decontamination method, the Responsible Body should
procedure is intended as a guide. Should spillage occur with a toxic or hazardous fluid
the Responsible Body with due recognition of possible hazards. Before using
then special precautions may be necessary.
check with the manufacturer the proposed method will not damage the
any cleaning or decontamination method, the Responsible Body should check
with the manufacturer the proposed method will not damage the equipment.
equipment.
Decontamination Certificate.
Prior to further use, the Responsible Body shall check the electrical safety of
Note: In the event of this equipment or any part of the unit becoming damaged or requiring
Prior to further use, the Responsible Body shall check the electrical safety of
the unit. Only if all safety requirements are met can the unit be used again. The
service, the item(s) should be returned to the manufacturer for repair accompanied by a
the unit. Only if all safety requirements are met can the unit be used again.
above procedure is intended as a guide. Should spillage occur with a toxic or
decontamination certificate. Copies of the Certificate are available from
The above procedure is intended as a guide. Should spillage occur with a toxic
hazardous fluid then special precautions may be necessary.
Distributor/Manufacturer. Appendix A of this instructions book may be copied and
or hazardous fluid then special precautions may be necessary.
Decontamination Certificate.
enlarged.
Note: In the event of this equipment or any part of the unit becoming damaged, or
At the end of life, this product must be accompanied by a Decontamination Certificate. See
Decontamination Certificate.
requiring service, the item(s) should be returned to the manufacturer for repair
section 6.3 and 6.4
accompanied by a decontamination certificate. Copies of the Certificate are
Note: In the event of this equipment or any part of the unit becoming damaged, or
available from Distributor/Manufacturer. Appendix A of this instructions book
requiring service, the item(s) should be returned to the manufacturer for repair
may be copied and enlarged.
accompanied by a completed decontamination certificate. Copies of the Certificate
At the end of life, this product must be accompanied by a Decontamination
are available from Distributor/Manufacturer.
Certificate. See section 6.3 and 6.4
At the end of life, this product must be accompanied by a completed
If in doubt please consult Customer support. Refer to section 10.
Decontamination Certificate.
Page 17 of 24
Page 20 of 24
and
o display the value and then use
to make the read value coincide with the value measured by the
If the equipment has been exposed to contamination, the Responsible Body
+
selected 0AD or SAD;0AD allows a
+
.
M6493 Issue 10.3
17
and
or
M7044 iss 3.3