Draper Ropewalker Инструкции Установка и эксплуатация - Страница 3

Просмотреть онлайн или скачать pdf Инструкции Установка и эксплуатация для Проекционный экран Draper Ropewalker. Draper Ropewalker 8 страниц. Electric projection screen with cable drop

Печатать страницу

Ropewalker

Section 2 - Mounting Ropewalker to Building Structure

Threaded Rod

Please Note: It is recommended that heavy items be hoisted up to the work area using appropriate machinery, i.e. hoisting lifts, block and tackle, etc.

When locating viewing surface and checking clearance for screen operation, remember surface is centered in the length of the case.

Regardless of mounting method used, the following points apply:

1. Screen should be lifted into position ONLY by end mounting brackets

or hoisting brackets. Keep case level by lifting both end plates at the

same time to prevent surface damage. Using more than one mounting

hole in each end plate ensures a much more stable installation. NEVER

attempt to lift screen along its length or in the middle.

2. Entire weight of unit MUST BE supported by end plates during

installation.

Please Note: DO NOT lift case at the center. Case leveling brackets

are ONLY used to reduce visible case deflection. Lift screen ONLY by

hoisting brackets. To ensure a safe installation, the entire weight of the

installed unit MUST BE supported by the mounting brackets.

Hoisting

Bracket

Section 3 - Electrical Connections

Screen operates on 110-120V, 60 Hz., 7.5A; or 220-240V, 50 Hz., 3A current draw.

Junction box is just above the bottom access panel at the left end of screen lift.

Figure 2

To access to the junction box

1. Open left side access panel by removing two

2. Remove two

5/16"

(2)

(8mm)

to expose red, brown, black, and white pigtail leads and green ground wire

(see Sec. 5, Ropewalker Wiring)

3. For optional low-voltage control, see Section 11.

4. Screen lift is shipped with internal wiring complete and control switch

boxed. Wire to connect screen to switch

should be furnished by installer. Connections should be made in accordance

with attached wiring diagram, and wiring should comply with national and

local electrical codes.

CAUTION: All operating switches should be "off" before connecting power.

(by others)

Figure 1

"-16

Threaded Rod

(10mm)

(use for adjusting deﬂection in extremely long units)

Hoisting

Bracket

JUNCTION

BOX

screws from side of case

(2)

hex head screws that secure cover to junction box

and switch

to power supply

(es)

3. Screen should be positively and securely supported so that vibration or abusive

pulling will not weaken installation.

4. Installer must ensure that fasteners used are of adequate strength and suitable

for mounting surface. Installer must also ensure that structure is of adequate

strength. Supporting hardware

5. Entire bottom of case must be readily accessible after installation is complete.

6. Front, back, and top of case must be straight — not forced to warp or bow.

7. Do not use case to support adjacent sections of ceiling.

8. Do not seal unit in ceiling until electrical connections have been made and screen

has been operated successfully.

(by others)

Mounting Brackets attached

to Threaded Rod

Case Leveling Bracket

Case Support Brackets

NOT for use in supporting weight of case.

Section 4 - Removing Shipping Bracket

1. Remove the electrical access panel

2. Remove the shipping bracket from the shaft. Discard

Figure 3-A

(Fig 2)

Figure 3-B

fully

(es)

(chains, cables, rods, etc.)

"-16

(10mm)

(use for adjusting deﬂection in extremely long units)

(by others)

shipping bracket

RED

(shown in

with hangtag, Fig. 3-A)

NOT for use i

page 3 of 8

Mounting

must be essentially vertical.

to Threa

Threaded Rod

(by others)

Hoisting

Bracket

Case

and locate the

(Section 3)

(Fig. 3-B)

SHIPPING

BRACKET

Case