DSC WT5500 Руководство по установке - Страница 3

Просмотреть онлайн или скачать pdf Руководство по установке для Система безопасности DSC WT5500. DSC WT5500 8 страниц. Wireless panel & keypad
Также для DSC WT5500: Краткое руководство по установке (2 страниц)

Печатать страницу

2. Enter keypad programming by pressing

3. Enter Section 998 at the keypad that was programmed. The keypad will now broadcast the label programming to

the PC9155. The PC9155 will then program the labels in others WT5500 keypads that have been enrolled by way

of the RF link.

NOTE: This operation may take several minutes.

4. When the keypad is finished press the # key to exit.

NOTE: Label broadcast from this keypad is only compatible with other WT5500 keypads.

Language Programming

Hold the (<>) keys for 2 seconds to enter language programming. Scroll to the desired language and press

select.

NOTE: If Section 077, Option 4 is turned off, language programming can only be performed while

in installers programming.

Enrolling the Keypad

The WT5500 must be configured in tandem with the PC9155 in order for the system to function as desired.

1. Turn on the PC9155 unit. The panel will be alert to any keypad enrollment activity for a period of two minutes. Note

that the unit's Ready and AC LEDs will be activated for this two-minute period.

2. A WT5500 must be turned on during this two-minute period for it to be assigned to the PC9155.

3. Simultaneously press and hold the * and # keys; by doing so you force the keypad to broadcast its ESN (electronic

security number). The keypad will intermittently flash its Ready and AC LEDs (one second on, one second off). This

indicates that the keypad is in enrollment mode.

4. When the keypad has been successfully enrolled - this should take less than 30 seconds - on the system, the mes-

sage 'Enrollment Successful' will be displayed on the keypad LCD for five seconds. The Ready and AC LEDs will

return to their ready state.

Any additional keypads to be added to this system can be enrolled in the same manner as described above. The sys-

tem will add each keypad to the next available slot, and this slot number will be displayed on the keypad's LCD dis-

play once the keypad has been successfully enrolled.

Programming Labels

1. Use this section to assign a meaningful name (e.g. Front Door, Hallway, etc) to each zone.

2. Enter keypad programming by pressing

label to be programmed.

3. Use the arrow keys (<>) to move the cursor underneath the letter to be changed.

4. Press the number keys 1 through 9, corresponding to the letter you require. For example, pressing number key 2

once will display the letter D; pressing it again will display the letter E; pressing it a third time will display the letter

F, and so on.

[1] - A, B, C, 1 [4] - J, K, L, 4 [7] - S, T, U, 7 [0] - Space

[2] - D, E, F, 2 [5] - M, N, O, 5 [8] - V, W, X, 8

[3] - G, H, I, 3 [6] - P, Q, R, 6 [9] - Y, Z, 9,0

5. When the required letter or number is displayed use the arrow keys (<>) to scroll to the next letter.

6. When you are finished programming the Zone Label, press Q. Scroll to 'Save' and press Q again.

7. Repeat Steps 2 through 5 until all Labels are programmed.

Installer Code

> 8 >

Installer Code

> 8 >

> . Enter the 3-digit section number for the

ASCII Characters

Changing Brightness/Contrast

LCD Keypads

1. Press [ ][6][Master code].

2. Use the arrow keys (<>) to scroll to either Brightness Control or to Contrast Control.

3. Press

to select the setting you want to adjust.

4. a) Brightness Control: There are multiple backlight levels. Use the arrow keys (<>) to scroll to the desired level.

5. b) Contrast Control: There are 10 different display contrast levels. Use the arrow keys (<>) to scroll to the desired

contrast level.

6. To exit, press #.

Changing the Buzzer Level

LCD Keypads

1. Press [ ][6][Master Code].

2. Use the arrow keys (<>)to scroll to Buzzer Control.

3. Use the arrow keys (<>) to scroll to the desired buzzer level among the 21 available selections.

4. To exit, press #.

Keypad Enrollment

Enter keypad programming by pressing

[0] Partition / Slot Assignment

Digit

Option

1st

Partition Assignment (0=Global Keypad)

2nd

Slot Assignment

[1]-[5] Function Key Assignment

Function Key Button

[1] Function Key 1 Assignment

[2] Function Key 2 Assignment

[3] Function Key 3 Assignment

[4] Function Key 4 Assignment

Installer's Code

> 8 >

> 000.

Valid

Default

Range

0 to 8

1 to 8

LED,ICON=1/LCD=8 I_____I

Valid

Defa

Function

Range

ult

00 to 32

Stay Arm

00 to 32

Away Arm

00 to 32

Chime On/Off I_____I_____I

00 to 32

Bypass

I_____I

I_____I_____I