DSC WT5500 Інструкція з монтажу Посібник з монтажу - Сторінка 3
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Система безпеки DSC WT5500. DSC WT5500 8 сторінок. Wireless panel & keypad
Також для DSC WT5500: Посібник зі швидкого встановлення (2 сторінок)
Друкувати сторінку
2. Enter keypad programming by pressing
3. Enter Section 998 at the keypad that was programmed. The keypad will now broadcast the label programming to
the PC9155. The PC9155 will then program the labels in others WT5500 keypads that have been enrolled by way
of the RF link.
NOTE: This operation may take several minutes.
4. When the keypad is finished press the # key to exit.
NOTE: Label broadcast from this keypad is only compatible with other WT5500 keypads.
Language Programming
Hold the (<>) keys for 2 seconds to enter language programming. Scroll to the desired language and press
select.
NOTE: If Section 077, Option 4 is turned off, language programming can only be performed while
in installers programming.
Enrolling the Keypad
The WT5500 must be configured in tandem with the PC9155 in order for the system to function as desired.
1. Turn on the PC9155 unit. The panel will be alert to any keypad enrollment activity for a period of two minutes. Note
that the unit's Ready and AC LEDs will be activated for this two-minute period.
2. A WT5500 must be turned on during this two-minute period for it to be assigned to the PC9155.
3. Simultaneously press and hold the * and # keys; by doing so you force the keypad to broadcast its ESN (electronic
security number). The keypad will intermittently flash its Ready and AC LEDs (one second on, one second off). This
indicates that the keypad is in enrollment mode.
4. When the keypad has been successfully enrolled - this should take less than 30 seconds - on the system, the mes-
sage 'Enrollment Successful' will be displayed on the keypad LCD for five seconds. The Ready and AC LEDs will
return to their ready state.
Any additional keypads to be added to this system can be enrolled in the same manner as described above. The sys-
tem will add each keypad to the next available slot, and this slot number will be displayed on the keypad's LCD dis-
play once the keypad has been successfully enrolled.
Programming Labels
1. Use this section to assign a meaningful name (e.g. Front Door, Hallway, etc) to each zone.
2. Enter keypad programming by pressing
label to be programmed.
3. Use the arrow keys (<>) to move the cursor underneath the letter to be changed.
4. Press the number keys 1 through 9, corresponding to the letter you require. For example, pressing number key 2
once will display the letter D; pressing it again will display the letter E; pressing it a third time will display the letter
F, and so on.
[1] - A, B, C, 1 [4] - J, K, L, 4 [7] - S, T, U, 7 [0] - Space
[2] - D, E, F, 2 [5] - M, N, O, 5 [8] - V, W, X, 8
[3] - G, H, I, 3 [6] - P, Q, R, 6 [9] - Y, Z, 9,0
5. When the required letter or number is displayed use the arrow keys (<>) to scroll to the next letter.
6. When you are finished programming the Zone Label, press Q. Scroll to 'Save' and press Q again.
7. Repeat Steps 2 through 5 until all Labels are programmed.
Installer Code
.
> 8 >
>
Installer Code
> 8 >
> . Enter the 3-digit section number for the
ASCII Characters
Changing Brightness/Contrast
LCD Keypads
1. Press [ ][6][Master code].
to
2. Use the arrow keys (<>) to scroll to either Brightness Control or to Contrast Control.
3. Press
to select the setting you want to adjust.
4. a) Brightness Control: There are multiple backlight levels. Use the arrow keys (<>) to scroll to the desired level.
5. b) Contrast Control: There are 10 different display contrast levels. Use the arrow keys (<>) to scroll to the desired
contrast level.
6. To exit, press #.
Changing the Buzzer Level
LCD Keypads
1. Press [ ][6][Master Code].
2. Use the arrow keys (<>)to scroll to Buzzer Control.
3. Use the arrow keys (<>) to scroll to the desired buzzer level among the 21 available selections.
4. To exit, press #.
Keypad Enrollment
Enter keypad programming by pressing
[0] Partition / Slot Assignment
Digit
Option
1st
Partition Assignment (0=Global Keypad)
2nd
Slot Assignment
[1]-[5] Function Key Assignment
Function Key Button
[1] Function Key 1 Assignment
[2] Function Key 2 Assignment
[3] Function Key 3 Assignment
[4] Function Key 4 Assignment
Installer's Code
> 8 >
> 000.
Valid
Default
Range
0 to 8
1
1 to 8
LED,ICON=1/LCD=8 I_____I
Valid
Defa
Function
Range
ult
00 to 32
03
Stay Arm
00 to 32
04
Away Arm
00 to 32
06
Chime On/Off I_____I_____I
00 to 32
14
Bypass
I_____I
I_____I_____I
I_____I_____I
I_____I_____I