Auber Instruments SYL-2615 Руководство по эксплуатации - Страница 2
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Контроллер Auber Instruments SYL-2615. Auber Instruments SYL-2615 7 страниц. Wi-fi bbq controller
Печатать страницуAUBER INSTRUMENTS
⑨ Probe 2 input for Food temperature.
⑩ Power output for fan control.
⑪ Power input for controller (12 VDC).
4. LCD Display Modes
Press
Normal Display
Momentarily
Pit: 73 Set:225
Food:71 Out:99
|
Press
SET
Momentarily
SET
>Step: 1 Pit: 225
Back
Cooking Profile
Figure 2. Switching between different display modes.
4.1 Normal Display Mode
Figure 3. Information displayed on the LCD in the normal operating mode.
① Pit temperature
② Food temperature
③ Set value for pit temperature
④ Output power (percentage)
4.2 Time-Checking Mode
|
Figure 4. Using Timer/Back key to check cooking time in single-step mode
(left) and in multi-step mode (right).
Press the Timer/Back key can tell you the current timer and step information.
In single step mode, press timer key will show the total running time after your
powered this controller up this time. In multi-step mode, pressing timer key will
display more information, including the elapsed time for current step and total
time for current step (first line); total elapsed time and current step number
(second line).
This key has two more functions: a) Press it in the parameter setting mode will
return back to the upper level menu. This provide a short cut to exit the current
menu. b) Cancel the open lid detection. For details, please see Note 8 in
section 6.2.2.
4.3 Cooking Profile Programming Mode
The controller's cooking profile can be either set to single-step mode (default)
or set to multi-step mode. In the single-step mode, the controller will try to
maintain the pit temperature at the set value of Step 1 as long as the controller
2019.07
Time Checking
Time Checking
Time:
Time: 0:02/ 9:00
OR
0:15
Tot: 0:10 Step: 2
> Control config
System config
Parameter Settings
|
is on. In the multi-step mode, up to 3 steps can be programmed. Each step
has its own set temperature for pit probe, and its step-ending criterion. A
cooking step can either end by timer or by food temperature. For details,
please check section 6.1.
4.4 Parameter Setting Mode
Figure 5. Access the menu of parameters using SET key.
5. Getting Started
Power on the controller by plugging the barrel connector from the 12 VDC
adapter to the power input port ⑪. Connect the pit probe (probe 1) to socket
⑧, food probe (probe 2) to socket ⑨. Configure the Wi-Fi connection from
your phone using AuberSmart app*. After you have set up the controller and
started fire in your smoker or grill, mount the blower to the smoker/grill, then
plug the blower connector to the fan output port ⑩.
Note *: Please check the supplementary manual for Wi-Fi configuration and
how to use the AuberSmart app.
6. Operation
All cooking profile settings and control parameters can be accessed both from
the device and from the AuberSmart app.
6.1 Set the Cooking Profile
The controller's cooking profile can be either set to single-step mode (default)
or set to multi-step mode. In the single-step mode, the controller will try to
maintain the pit temperature at the set value of Step 1 as long as the controller
is on. In the multi-step mode, up to 3 steps can be programmed. Each step
has its own set temperature for pit probe, and its step-ending criterion. A
cooking step can either end by timer or by food temperature. To switch
between single-step mode and multi-step mode, please check section 6.1.3.
6.1.1 Single-Step Mode
In this mode, you can only access and change the target pit temperature of
Step 1 from the device. The controller will try to maintain the smoker
temperature at the set temperature of Step 1 continuously as long as the
controller is powered on. If this controller is powered off and turned back on
again, it will resume operating in this mode. You can still view and change
other settings in Cooking Profile from the app, but they don't apply to this
mode.
To change the set temperature in single-step mode, press SET key once, it
will show "Step: 1" and the current target pit temperature in the top line. A
curser ">" will be shown on the left indicating which line will be selected. Press
SET key once, the current set temperature should start blinking. Use ▲ and
▼ keys to change the set temperature. When finished, press the SET again
to confirm the change. That number will stop blinking. Press the Timer/Back
key to exit the menu. Or use ▲ or ▼ key to scroll to "Back" and then press
SET key to exit. The display will return to the normal display mode if no key is
pressed in 14 seconds.
WWW.AUBERINS.COM
P2/7