Casio 2198 Общее руководство - Страница 7

Просмотреть онлайн или скачать pdf Общее руководство для Смотреть Casio 2198. Casio 2198 9 страниц.

Печатать страницу

To calibrate the temperature

1. Display the barometric pressure/tempera-

2. Hold down A until the display clears.

hPa mb

• The "OFF" indicator appears when the

factory setting is being used for the

A S

calibration.

3. Each press of D increases the displayed

hPa mb

TEMP ADJ

A S

• Any time you calibrate the temperature, the message "TEMP ADJ" appears

on the display. This message remains on the display in any mode in which

the temperature is displayed.

• If you have selected Fahrenheit as your unit of measurement, the above

operations change the reading by 0.2°F.

• Pressing B and D at the same time returns to the "OFF" display.

4. After calibrating the temperature, press A to return to the Barometric

Pressure/Temperature screen.

• If you do not operate any button for a few minutes while the temperature

digits are flashing, the flashing stops and the watch goes back to the

Barometric Pressure/Temperature screen.

WARNING INDICATORS

Warning indicators appear whenever any of the conditions described below

occur. Appearance of a warning indicator causes any measurement operation

that is currently underway to stop. Warning indicators appear in the upper

display, and this causes "– – –" to replace any directional, altitude, barometer,

or temperature values on the display.

Abnormal Magnetic Field Indicator

This indicator appears whenever the Digital

Compass has a problem obtaining a correct

reading. This condition could indicate that

the watch is within a very high magnetic field,

and so you should try moving to another

location. Also, see "Digital Compass

Precautions" for further information on

conditions that cause errors.

Low Battery Indicator

This message indicates that battery power is

too low to perform the measurement. It

appears whenever battery power drops below

a certain level, or when you try to use this

watch under very cold conditions (below about

–10.0°C/14.0°F).

If the "BAT" message appears because of use under cold conditions, it should

clear (and normal operation should return) after the watch is brought back to

normal temperature.

If battery power is low (indicated "BAT" appears under normal temperatures),

you should have the batteries replaced as soon as possible. Note that

replacement of the batteries causes all memory contents to be cleared.

Sensor Malfunction Indicator

This message indicates malfunction of

pressure sensor circuitry. Whenever a sensor

malfunction initially occurs, the "ERR"

messages flashes on the display and a buzzer

sounds for three seconds.

Note that calibrating the Digital Compass may cause the "ERR" message to

appear. In this case, the message does not indicate sensor malfunction, and

should be corrected if you re-calibrate the Digital Compass.

Important!

• If the sensor is malfunctioning when it comes time for a barometric pressure

measurement to be taken, the barometric pressure value appears as

"– – – –" on the display and the corresponding point on the barometric

pressure graph is left blank.

• There may be cases where the "ERR" or "BAT" message is cleared once

you change modes. In this case, you can continue using the watch normally

unless the error warning message reappears.

Whenever there is a sensor malfunction, be sure to take the watch to an

authorized CASIO distributor or Service Center as soon as possible.

ture in the Timekeeping Mode.

"OFF" or the temperature value should be

flashing on the display.

temperature by 0.1°C while pressing B

decreases it. Holding down either button

changes the value at high speed.

ALARM FUNCTIONS

Mode indicator

Five independent daily alarms can be set.

Alarm No.

Each alarm lets you set the hour and minutes.

When the Daily Alarm is on, the alarm sounds

for 20 seconds at the preset time each day.

Press any button to stop the alarm after it

starts to sound.

When the Hourly Time Signal is on, the watch

beeps every hour on the hour.

• In the Alarm Mode, the segments in the

graphic display create a rotational

movement effect while an alarm is sounding.

To set alarms

Hour Minutes

1. Use C to enter the Alarm Mode.

Graphic display

Alarm on

2. Press D to select Alarm 1 through 5.

indicator

Alarm 1

Alarm 2

Hourly Time Signal

3. After you select an alarm, hold down A until the hour digits flash on the

display. The hour digits flash because they are selected .

• At this time, the alarm is automatically switched on.

4. Press C to change the selection in the following sequence.

Hour

5. Press D to increase the selected digits and B to decrease them. Holding

down either button changes the selection at high speed.

• The format (12-hour or 24-hour) of the alarm time matches the format you

selected for normal timekeeping.

• When setting the alarm time using the 12-hour format, take care to set the

time correctly as morning (no indicator) or afternoon (P).

6. After you set the alarm, press A to return to the Alarm Mode.

To switch an alarm or the Hourly Time Signal on and off

1. In the Alarm Mode, press D to select an alarm or the Hourly Time Signal.

2. When the alarm or Hourly Time Signal you want to is selected, press E to

switch it on and off.

Indicates alarm is ON.

Indicates Hourly Time Signal is ON.

• If any alarm is on, the alarm on indicator (

you change to another mode.

To test the alarm

Hold down D while in the Alarm Mode to sound the alarm.

STOPWATCH FUNCTIONS

Mode indicator

The Stopwatch Functions let you measure

Graphic

elapsed time, split times, and two finishes.

display

1/100 second

The range of the stopwatch is 23 hours, 59

minutes, 59.99 seconds.

Stopwatch functions are available in the

Stopwatch Mode, which you can enter using

• In the Stopwatch Mode, the graphic display

indicates the counting of seconds.

A S

Seconds

Hours

Minutes

(a) Elapsed time measurement

Start

Re-start

Stop

(b) Split time measurement

Split release

Start

Split

Start

Split

Stop

Second runner finishes.

First runner

Record time of first runner.

finishes.

1998/2198-7

Alarm 3

Alarm 4

Alarm 5

Minutes

) is shown on the display when

Clear

Stop

Clear

Split release

Clear

Record time of

second runner.