Dürr NDT ScanX Discover HC Инструкции по быстрому запуску - Страница 2
Просмотреть онлайн или скачать pdf Инструкции по быстрому запуску для Принтер "все в одном Dürr NDT ScanX Discover HC. Dürr NDT ScanX Discover HC 4 страницы. Mobile computed radiography system
Также для Dürr NDT ScanX Discover HC: Инструкции по быстрому запуску (4 страниц)
Печатать страницу
Box contents
Unpacking
As listed below, each ScanX System is shipped in a single carton
containing the ScanX main assembly and associated accessory
kit. Unpack each component of the ScanX and inspect for physi-
cal damage such as scratched panels, damaged connectors, etc.
If any damage is noted, immediately notify your authorized
dealer so corrective action can be taken. Save all cartons and
packing materials to protect the ScanX in the event of future
transport or shipping.
Included System Components
Each ScanX system consists of the indicated main assembly
and accessory kit as listed. Refer to the TECHNICAL DATA
section of the Operator's Manual included on the supplied CD
Disk for ratings and identification for specific ScanX models.
Verify that all listed items were received. If any item is missing,
notify your dealer.
Make sure to read and follow the Operator's Manual included as a PDF file on the supplied CD Disk to ensure that your ScanX
Important:
gives the highest level of service. Please note that the Operator's Manual is also available on the website (www.scanx-ndt.com).
Setup & operation
ScanX Imaging Software and Device Drivers Installation
The user must provide appropriate and compliant computer hardware where ScanX View or an authorized third-party imaging software is
installed. In addition, USB device drivers must also be installed to operate ScanX. When using ScanX View, these drivers are automatically
installed during the software installation. When using a third-party imaging software, drivers are installed via the Setup program provided on
the CD disk included with ScanX. Normally, this program runs automatically when the CD is inserted into the drive for the first time.
If not, run the Setup program located in the root directory of the CD (typically D:\AutoRun.exe).
ScanX Connections
As shown by the illustration at right, connecting
the ScanX for operation consists of the following
1. Connect the ScanX to the computer
via supplied USB cable.
2. Connect the ScanX to power source
via supplied line cord.
ScanX Operation
Operate the ScanX connected to a properly set up computer as follows:
1. Place the ScanX rocker switch to the ON (I) position.
2. Press the READY switch to turn ON the ScanX.
3. Verify that the READY indicator illuminates.
4. Activate the scanner via the Imaging Software.
5. Verify that all track status indicators illuminate green.
6. Minimize exposure to ambient light and insert the PSP into the ScanX inlet
with the sensitive (front) side of PSP towards the ScanX.
7. Verify that all track status indicators illuminate yellow.
8. Observe that the scanned PSP exits through the scanner arch.
Manufactured by Air Techniques for:
DÜRR NDT GmbH & Co. KG
Höpfigheimer Straße 22
74321 Bietigheim-Bissingen, Germany
Phone: +49 7142 99381-0 · Fax: +49 7142 99381-299
www.scanx-ndt.com
System Components
Model
ScanX Discover Imaging Plate Scanner
Quick Start Instructions
Accessory Kit containing:
3-meter USB cable
Fuse Kit (5A, 250VAC, Fuse; qty 2)
CD Disk containing Drivers and
Operator's Manual
Country specific Mains cable
Main Power
Switch (1/0)
Note:
The Main Power Switch is the
Mains disconnect device.
Page 2 of 4
ScanX
ScanX
Discover HR
Discover HC
2138100010
2138100012
2138100301
2138100301
2138100043
2138100043
Type B USB Connector
IEC Connector
ERASER Switch
Eraser
Status
Scanner
Ready/Standby
Indicator
Track Status
Status Indicator
Indicators
P/N D5421DQ, Rev A (2138100301) - May 2017
Type A USB
Connector to
Computer
Line Cord
From
Mains
Outlet
READY
Switch