4O3A Rotator Genius Руководство - Страница 4
Просмотреть онлайн или скачать pdf Руководство для Контроллер 4O3A Rotator Genius. 4O3A Rotator Genius 20 страниц.
Печатать страницу2.2 Network / Offset Setup
IP address configuration is done using the on device settings menu (using the device buttons and LCD display).
Enter the menu by holding the
When you navigate to an item in the menu this item will be considered selected.
Select Rotator
will be abbreviated as
Settings menu items:
Configures the IP address of the device. The default IP address is 192.168.1.250
LOCAL IP
When the LOCAL IP item is selected press the
The first octet (first three number portion of the address) will start blinking. This is 192 in the
default address case. Use
When done, press the
Again use the
Repeat the same procedure for the last two octets. The selected octet will always blink.
When done with all 4 no value will be blinking and the address will remain static.
Use
▲
to select the next item.
Configures the netmask of the device. The default netmask is 255.255.255.0
NETMASK
When the NETMASK item is selected press the
The first octet (first three number portion of the address) will start blinking. That is 255 in the
default case. Use
When done, press the
use the
▲
Repeat the same procedure for the last two octets. The selected octet will always blink.
When done with all 4 no value will be blinking and the netmask will remain static.
Use
▲
to select the next item.
GATEWAY
Configures the gateway address of the device. The default gateway address is 192.168.1.1
When the GATEWAY item is selected press the
The first octet (first three number portion of the address) will start blinking. This is 192 in the
default address case. Use
When done, press the
Again use the
Repeat the same procedure for the last two octets. The selected octet will always blink.
When done with all 4 no value will be blinking and the address will remain static.
Use
▲
to select the next item.
PORT
Configures the TCP port for the RG Windows app. Default port is set to 9006.
It is strongly recommended to keep it at its default value and change it only if necessary.
In case a service on your network uses the same port change it to some other value.
Remember to change it in the Windows application as well.
Again, use
While in editing mode, the item will blink.
Press the
Use
▲
button to navigate to next item.
OFFSET R1
This is where you set the magnetic declination for Rotator 1.
This value varies depending on your current geographical location. You can calculate it online
using a service such as:
It is a value to be subtracted or added to the azimuth value.
It will be subtracted if the value is negative.
It will be added if the value is positive.
Press the
Use
▲
and
Press the
⬆
Back to table of contents
MENU
button for two seconds. Use
Select.
▲
and
▼
Select
button to move to the next octet. This is 168 in the default case.
▲
and
▼
buttons to alter the value then press
▲
and
▼
buttons to increase or decrease this value.
Select
button to move to the next octet. 255 in the default case. Again
and
▼
buttons to alter the value then press
▲
and
▼
Select
button to move to the next octet. This is 168 in the default case.
▲
and
▼
buttons to alter the value then press
▲
and
▼
to increase and decrease the value.
Select
button when done.
http://www.ngdc.noaa.gov/geomag- web/
Select
button to edit the item.
▼
buttons to increase or decrease its value.
Select
button when done.
▲
and
▼
buttons to navigate between items.
Select
button to edit the IP address.
buttons to increase or decrease this value.
Select
Select
button to edit the netmask.
Select
Select
button to edit the IP address.
buttons to increase or decrease this value.
Select
to move to the next octet.
to move to the next octet.
to move to the next octet.
Page 4