ADEMCO 5808 Инструкции по установке

Просмотреть онлайн или скачать pdf Инструкции по установке для Дымовая сигнализация ADEMCO 5808. ADEMCO 5808 4 страницы. Photoelectronic smoke/heat detector with built-in wireless transmitter
Также для ADEMCO 5808: Инструкции по установке (5 страниц)

Печатать страницу

5808 Photoelectronic Smoke/Heat Detector with

Built-in

Built-in Wireless

Built-in

SPECIFICATIONS

Power Source:

Maintenance Limits (Maintenance signal

is activated at either smoke level):

Height:

Diameter:

Weight:

Operating Ambient Temperature Range:

Operating Humidity Range:

Heat Sensor:

Agency Listings:

Before installing detectors, please thoroughly read these installation instruc-

tions and Manual I56-407, Guide for Proper Use of System Smoke Detectors,

which provides detailed information on detector spacing, placement, zoning,

wiring, and special applications. Copies of this manual are available from

ADEMCO.

NOTICE: This manual should be left with the owner/user of this equipment.

IMPORTANT: This detector must be tested and maintained regularly following

NFPA 72 requirements. The detector should be cleaned at least once a year.

WARNING: Do not use the maintenance signal as an indication that the

detector has reached the limits of its nominal sensitivity range. Maintenance

only indicates that the detector may need cleaning or can no longer respond

to smoke and shall not be used as a sensitivity indicating means.

GENERAL DESCRIPTION

The 5808 photoelectronic smoke/heat detector with built-in wireless transmit-

ter is intended for use with wireless alarm systems that support QED 5800

series devices. Refer to QED control communicator installation instructions

for compatibility. The 5808 smoke/heat detector can be used with 5881 series

(L, M, H) and 5881EH receivers for residential installations. The 5808 smoke/

heat detector can be used with the 5881EH receiver for commercial installa-

tions. The transmitter can send alarm, tamper, maintenance (when QED

control panels are equipped to process maintenance signals), and battery

condition messages to the QED system's receiver. The maintenance signal

will either indicate that the photo chamber requires cleaning or that the detector

can no longer respond to smoke and may need replacement. Refer to the

wireless system's instructions for the maximum number of transmitters that can

be supported.

The 5808 sounds its built-in horn when smoke reaches the detector (the

LED also flashes rapidly) or when the air temperature reaches 135° F (the

LED flashes normally, about once every 40 seconds). A message is also

sent to the wireless QED control panel and the smoke detector's ID number

is displayed at the console. The alarm message is transmitted every 4

seconds until the smoke condition has cleared and the detector has reset.

About 1 second after the horn stops, a RESTORE message is transmitted

to the QED control panel and the ID number can be cleared from the panel.

During normal, maintenance, and low battery conditions, the LED flashes

approximately once every 40 seconds.

BATTERY INSTALLATION AND REPLACEMENT

The 5808 is powered by two 3-volt CR123A or DL123A Lithium batteries

(included). The detector checks for low batteries at every normal LED flash.

If a low battery is detected, the transmitter sends a low battery message to

the QED control panel, which beeps and displays the detector's ID. This

condition will exist for a minimum of seven days, and then the detector's

horn will "chirp" about every 40 seconds. The batteries should be replaced

BEFORE the chirps begin. BE SURE TO REPLACE BOTH BATTERIES

WITH FRESH ONES.

AD300-00-00

ﬁ

For use with QED control panel ONLY!

Wireless

Wireless T T T T T ransmitter Installation Instructions

Wireless

ransmitter Installation Instructions

Wireless

ransmitter Installation Instructions

Two 3-volt CR123A Lithium Batteries (included). (Replace with Duracell DL123A, Sanyo

CR123A, Panasonic CR123A, ADEMCO 466, or Varta CR123A.)

Hot Sensitivity: 0.65% ± 0.15% per foot

Cold Sensitivity: less than 6% per foot

2.5 inches (14 cm)

5.5 inches (64 mm)

0.7 lb. (310 g)

4.4° to 37.8° C (40° to 100° F)

5% to 95% Relative Humidity

135° F Fixed Temperature Electronic Thermistors

UL 217; UL 268 – Residential, Commercial Installations

To replace batteries:

Remove the detector from its mounting plate by twisting the detector counter-

clockwise. Remove batteries, if replacing, and dispose properly.

Install two new 3-volt CR123A Lithium batteries in the battery compart-

ment. Follow the polarity diagram inside the compartment.

3. Reinstall the smoke detector onto the mounting plate by turning the

detector clockwise.

4. Test the detector as described in the TESTING TRANSMITTER SIG-

NAL section of this manual. The LED should flash about once every 40

seconds to indicate normal operation. If the batteries are not installed

correctly, the smoke detector will not operate and the batteries may be

damaged. If the detector does not appear to be sending a signal during

any of the tests, check for correct battery installation.

Indicator Light

Pulsing: Normal/Thermal Alarm

Fast Blink: Smoke Alarm

None: Call for Service

Test Module

Port

Figure 1. 5808 Wireless Smoke/ Heat Detector

PROGRAMMING

The smoke detector's ID must be enrolled in the QED control panel during

installation of the system. The QED control panel should be programmed

to enroll the 5808 as an "RF" unit (must be programmed as "supervised RF"

for UL installations).

Put the QED control panel in the program

ming mode and perform the following:

With the QED control panel, program the detector as loop 1 and either

manually enter the serial number that is on the label of the 5808, or press

the test switch to cause a transmission. Additional transmissions will cause

the "Confirm" display to appear on the keypad display.

See the QED control unit's installation instructions for further details.

ADEMCO, 165 Eileen Way, Syosset, New York 11791

Previous Menu

Test Switch

A78-2332-01

I56-918-06