Autopage MA-200 Руководство по установке - Страница 7

Просмотреть онлайн или скачать pdf Руководство по установке для Система безопасности Autopage MA-200. Autopage MA-200 8 страниц. 2-way remote control motorcycle alarm
Также для Autopage MA-200: Руководство по эксплуатации (13 страниц)

Печатать страницу

30/ 60/ 90seconds timed output = A 30, 60, or 90-second timed output will send a signal for 30, 60, or 90

seconds, respectively, when the channel 3 / 4 transmitter button(s) are pressed.

III

ALARM FEATURE "

" PRORAMMING:

1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.

2. Push the Valet switch 6 times and hold in on the 6

then release the valet switch. You are now in the Alarm feature 'III' programming mode.

3. Press and release the transmitter button 'A' corresponding to the feature 'A' you want to program.

Press

One Chirp /

LED one pulse

ransmitte

Button

Factory Default Setting

Exit the programming mode. (3 long chirp to confirm this exit.)

Override Without Password Pin Code

( Press & hold

delete the Password pin code)

Adjust and Test the sensitivity level of the

Shock Sensor. (Press & hold

2 seconds)

Exit:

Turn the Ignition to the 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.

Password Pin Code Setup:

1. Turn the Ignition 'switch 'ON/OFF' 3 times and stay in OFF position.

2. Push the Valet switch 6 times and hold in on the 6

then release the valet switch. You are now in the Alarm feature 'III' programming mode.

3. Press and release

button on the transmitter once, [2] LED flash, [2] siren/horn chirp to indicate you

are in features "Password Pin Code Programming mode".

4. Within 15 seconds, begin to enter your selected number by pressing and releasing the valet Switch from

1 – 9 times.

5. Finish by turning the ignition switch to the "ON" position.

If the new password code was accepted, the unit would report back the newly entered code, by flashing

the LED, first indicating the first digit code has been memorized. The unit will report the new code three

times with a one-second pause between each code.

Note: If 15 seconds of inactivity expire, or

unit will revert back to the last successfully stored code. 3 long chirps will confirm exit. The unit will revert

back to the last successfully stored code

Delete Password Pin Code / Override Without Password Pin Code (Factory default setting):

1. Turn the Ignition 'switch 'ON/OFF' 3 times and stay in OFF position.

2. Push the Valet switch 6 times and hold in on the 6

then release the valet switch. You are now in the Alarm feature 'III' programming mode.

3. Within 15 seconds, press and hold

Deleting the Password Pin Code.

Adjust and Test the sensitivity level of the Shock Sensor

1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.

2. Push the Valet switch 6 times and hold in on the 6

then release the valet switch. You are now in the Alarm feature 'III' programming mode.

3. Press and hold the

button on the transmitter for 2 seconds. 2 Chirp will indicate the unit is ready to

accept adjustments of the "Full-Alarm" sensitivity.

4. Pressing the

button on the transmitter once will decrease the sensitivity level by one, each time a

decrease is made the siren/horn chirp will respond number of chirp which indicates level of

sensitivity.

5. Pressing the

button on the transmitter once will increase sensitivity level by one, each time an

increase is made the siren/horn chirp will respond number of chirp which indicates level of

sensitivity.

MA200 IN REV.A

push until three chirps with a long chirp is heard

Two Chirps /

LED two pulses

Override With Password Pin Code

(Password pin code programming)

button for 4 seconds to

button for

push until three chirps with a long chirp is heard

button on the transmitter is press during of above steps, the

push until three chirps with a long chirp is heard

button on the transmitter for 4 seconds. One chirps to confirms

push until three chirps with a long chirp is heard

Oct/23/2006