GAME SolarPRO 4721 Руководство пользователя - Страница 7
Просмотреть онлайн или скачать pdf Руководство пользователя для Нагреватель для плавательного бассейна GAME SolarPRO 4721. GAME SolarPRO 4721 13 страниц. Curve heater
Также для GAME SolarPRO 4721: Руководство пользователя (12 страниц)
Печатать страницу
Hose to
Pool
Collar
Hose Clamp
Hose Adapter
Reducer
(if needed)
Hose to
Pool
Hose to
Pool
Flat
Collar
Gasket
Hose Adapter
Intex Adapter
~ OR ~
Bestway Adapter
3. Heater – Pool Connections
NOTE: If your pool is plumbed with heavy-duty, reinforced flex hose, contact your local pool retailer for an available GAME
adapter kit (item 4553).
A) Pools with 1¼" or 1½" Diameter Unthreaded Hoses
Connect the hose adapter into the heater port. Secure with the collar. Attach the hose (from the filter) and secure with a hose clamp.
Repeat on the other side of the heater, connecting the hose to the pool. See figure 2.
OR
B) Pools with 2¼" Diameter Threaded Hoses
Connect the hose adapter into the heater port. Secure with the collar. Attach the adapter for either Intex (use flat gasket as shown if
needed) or Bestway to the heater port. Be sure the o-ring is in the adapter before attaching. Attach the hose (from the filter) and secure
with a hose clamp. Repeat on the other side of the heater, connecting the hose to the pool. See figure 3.
NOTE: If solar heater needs to be further from the filter than the hoses allow, you may need to purchase a longer hose with the
1½" diameter openings. A 1½"-1½" coupler is needed to allow you to connect an additional hose if necessary (not included).
In this case make certain you have two hose clamps to secure the hoses to the coupler. If the hoses are too wide to fit the hose
connector, usevtt the 1¼"-1½" tube reducer on the hose connector and continue.
CAUTION: ENSURE ALL HOSE CONNECTIONS ARE TIGHT AND THE HOSES ARE NOT KINKED OR BENT AT SEVERE ANGLES. IF
THE HOSES ARE LEAKING, CHECK TO MAKE SURE ALL OF THE PARTS THAT HAVE O-RINGS HAVE THEM ATTACHED AND ARE
SCREWED ON TIGHTLY. DO NOT OVER TIGHTEN HOSE CLAMPS (35 IN/LB MAX TORQUE)
4. Initial Operation
Once the solar heater has been assembled and the hoses are connected to the filter pump and pool return, unblock the flow of water
into the pool return hose and turn on the pump and filter system. Bubbles will shoot out of the return nozzle into the pool initially
while air is pushed out of the solar heater. If this persists for longer than 2 or 3 minutes, check for and repair any leaks in the hoses
or connections.
FOR BEST RESULTS: To reduce heat loss, use a pool cover on your pool overnight, run your filter system during daylight hours
and cover the solar heater at night (if running the system).
Pools with 1¼" or 1½" Diameter Unthreaded Hoses
Figure 2
Pools with 2¼" Diameter Threaded Hoses
Figure 3
7
Hose from
Filter/Pump
Collar
Hose Adapter
Hose Clamp
Reducer
(if needed)
Hose from
Filter/Pump
Hose from
Filter/Pump
Flat
Collar
Gasket
Hose Adapter
Intex Adapter
~ OR ~
Bestway Adapter
SAVE THESE INSTRUCTIONS