GAME SolarPRO 4721 Kullanıcı El Kitabı - Sayfa 7

Yüzme Havuzu Isıtıcısı GAME SolarPRO 4721 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. GAME SolarPRO 4721 13 sayfaları. Curve heater
Ayrıca GAME SolarPRO 4721 için: Kullanıcı El Kitabı (12 sayfalar)

Sayfayı Yazdır

Hose to

Pool

Collar

Hose Clamp

Hose Adapter

Reducer

(if needed)

Hose to

Pool

Hose to

Pool

Flat

Collar

Gasket

Hose Adapter

Intex Adapter

~ OR ~

Bestway Adapter

3. Heater – Pool Connections

NOTE: If your pool is plumbed with heavy-duty, reinforced flex hose, contact your local pool retailer for an available GAME

adapter kit (item 4553).

A) Pools with 1¼" or 1½" Diameter Unthreaded Hoses

Connect the hose adapter into the heater port. Secure with the collar. Attach the hose (from the filter) and secure with a hose clamp.

Repeat on the other side of the heater, connecting the hose to the pool. See figure 2.

B) Pools with 2¼" Diameter Threaded Hoses

Connect the hose adapter into the heater port. Secure with the collar. Attach the adapter for either Intex (use flat gasket as shown if

needed) or Bestway to the heater port. Be sure the o-ring is in the adapter before attaching. Attach the hose (from the filter) and secure

with a hose clamp. Repeat on the other side of the heater, connecting the hose to the pool. See figure 3.

NOTE: If solar heater needs to be further from the filter than the hoses allow, you may need to purchase a longer hose with the

1½" diameter openings. A 1½"-1½" coupler is needed to allow you to connect an additional hose if necessary (not included).

In this case make certain you have two hose clamps to secure the hoses to the coupler. If the hoses are too wide to fit the hose

connector, usevtt the 1¼"-1½" tube reducer on the hose connector and continue.

CAUTION: ENSURE ALL HOSE CONNECTIONS ARE TIGHT AND THE HOSES ARE NOT KINKED OR BENT AT SEVERE ANGLES. IF

THE HOSES ARE LEAKING, CHECK TO MAKE SURE ALL OF THE PARTS THAT HAVE O-RINGS HAVE THEM ATTACHED AND ARE

SCREWED ON TIGHTLY. DO NOT OVER TIGHTEN HOSE CLAMPS (35 IN/LB MAX TORQUE)

4. Initial Operation

Once the solar heater has been assembled and the hoses are connected to the filter pump and pool return, unblock the flow of water

into the pool return hose and turn on the pump and filter system. Bubbles will shoot out of the return nozzle into the pool initially

while air is pushed out of the solar heater. If this persists for longer than 2 or 3 minutes, check for and repair any leaks in the hoses

or connections.

FOR BEST RESULTS: To reduce heat loss, use a pool cover on your pool overnight, run your filter system during daylight hours

and cover the solar heater at night (if running the system).

Pools with 1¼" or 1½" Diameter Unthreaded Hoses

Figure 2

Pools with 2¼" Diameter Threaded Hoses

Figure 3

Hose from

Filter/Pump

Collar

Hose Adapter

Hose Clamp

Reducer

(if needed)

Hose from

Filter/Pump

Hose from

Filter/Pump

Flat

Collar

Gasket

Hose Adapter

Intex Adapter

~ OR ~

Bestway Adapter

SAVE THESE INSTRUCTIONS