KitchenAid KGCV465MSS03 Руководство по установке - Страница 8

Просмотреть онлайн или скачать pdf Руководство по установке для Варочная панель KitchenAid KGCV465MSS03. KitchenAid KGCV465MSS03 20 страниц. 36" pro line series commercial style cooktop

Печатать страницу

Check the

Electronic

ignition

System

initial

lighting

Surface burners use electronic ignitors

in place of standing pilot& When the

cooktop control knob is pushed in and

turned to the "LITE" position, the system

creates a spark to light the burner. This

sparking continues until the control knob

is turned to the desired setting.

TripleTier

F_ame

standard

burner

burners

Push in and turn the surface

burners to "LITE" position. The surface

burner flame should light within 4

seconds.

After Hghting

the burners,

turn the

control

knobs

"OFF",

If burners do not light properly, turn

control knob to the "OFF" position. Check

that burner cap is in the proper position.

Check that power supply cord is plugged

in and that circuit breaker has not tripped

or house fuse has not blown. Check that

the shutoff valve is in the "ON" position.

Check operation again.

If a surface burner does not light at this

point, contact your KitchenAid dealer for

assistance.

Standard Burner Adjustment

Push in and turn each control knob to the

'%0" position. The "LO" setting of each

burner has been factory set to the lowest

position available to provide reliable

reignition of the burner. If it does not stay

lit on the "LO" position, check "LO"

position as follows:

a. Turn control knob to "LITE" until burner

ignites.

b. Quickly turn control knob down to '%0"

position.

c. If burner goes out. readjust valve as

follows:

Remove control knob.

standard

burner

adjustment

valve stem

For standard burner adjustment:

Insert

a flat-blade screwdriver into the hollow

valve stem and engage the slotted screw.

Flame size can be increased or

decreased by turning the screw. Adjust

flame until you can quickly turn control

knob from "H!" to "LO" position without

extinguishing the flame. Flame should be

as small as possible without going out.

TripJeTier Burner Regulation

Simmer Burner "LO".

Push in and turn the control knob to the

"SIMMER BURNER LO" position. The

"SIMMER BURNER LO" setting of the

TripleTier burner has been factory set to

the lowest position available to provide

reliable reignition of the burner. If it does

not stay lit on the "SIMMER BURNER LO"

position, check "SIMMER BURNER LO"

position as follows:

a. Turn control knob to "LiTE" until burner

ignites.

b. Quickly turn control knob down to

"SIMMER BURNER LO" position.

c. If burner goes out. readjust the dual

valve as follows:

Remove TripieTier control knob.

s_mmer

burner

regulation

For simmer burner flame adjustment:

Insert a flat-blade screwdriver into

adjustment locations shown and engage

the slotted screw. Flame size can be

increased or decreased by turning the

screw. Adjust flame until you can quickly

turn control knob from "SIMMER

BURNER HI" to "SIMMER BURNER LO"

position without extinguishing the flame.

Flame should be as small as possible

without going out.

For power burner "LO" adjustment:

Push in and turn the control knob to the

"POWER BURNER LO" position. The

"POWER BURNER LO" setting of the

TripleTier burner has been factory set to

the lowest position available to provide

reliable reignitJon of the burner. Jf it does

not stay lit on the "POWER BURNER LO"

position, check "POWER BURNER LO"

position as follows:

a. Turn control knob to "LITE" until burner

ignites.

b. Quickly turn control knob down to

"POWER BURNER LO" position.

c. Jf burner goes out. readjust the dual

valve as follows:

Remove TripleTier control knob.

power burner

regulation

For power burner flame adjustment:

Insert a flat-blade screwdriver into

adjustment locations shown and engage

the slotted screw. Flame size can be

increased or decreased by turning the

screw. Adjust flame until you can quickly

turn control knob from "POWER

BURNER HI" to "POWER BURNER LO"

position without extinguishing the flame.

Flame should be as small as possible

without going out.

ports

,//

.......

typ oo

surfaoo

U U U i

burner flame at

highest setting

Check flame on "HI" for a blue

color. It should be clean and soft in

character. No yellow tip, blowing or lifting

of flame should occur. Occasional orange

flashes are normal and reflect different

elements in the air or gas.