ALIBI ALI-NS4036RE Руководство по быстрой установке - Страница 2
Просмотреть онлайн или скачать pdf Руководство по быстрой установке для Камера безопасности ALIBI ALI-NS4036RE. ALIBI ALI-NS4036RE 6 страниц. 6mp 270 ft ip bullet camera
Печатать страницу
Mounting surface
Junction box
Drill template
Junction box mounting screws (4)
3.
Drill holes in the mounting surface for the mounting screws and extension cables (if necessary).
4.
Secure the Junction box to the mounting surface using appropriate fasteners.
5.
Route the Ethernet and power extension cables between the junction box and the devices they
connect to. Do not apply power to the extension cables at this time.
6.
Attach the safety cable in the junction box to the tab in the mounting base of the camera.
To mount the camera onto a surface without the junction box
For this mounting option, the drop cables can be routed through the mounting surface, or through the
cable channel in the mounting base.
Mounting base
screws (4)
1.
Determine the best fasteners for securing the camera mounting base to mounting surface. The
mounting hardware provided may be suitable for some surfaces.
2.
Remove the junction box from the camera assembly by removing the four mounting base captive
screws.
3.
Using the camera mounting base as a template, mark the locations of the holes for the mounting
screws. Also mark the location of a hole for the camera drop cables if needed.
4.
Route extension cables from the power source and LAN switch (or LAN with PoE) to the
mounting location.
To mount the camera onto an electrical box
1.
Install a double-gang electrical box at the location where the camera will be installed.
2.
Attach the adapter plate provided to the electrical box using four (4) screws.
Double-gang box
Adapter plate
Adapter plate mounting screws (4)
3.
Remove the junction box from the camera assembly by loosing the four mounting base captive
screws.
4.
Attach the adapter plate to the double-gang box using at least two (2) screws.
2
www.observint.com
Safety cable
Orientation mark
Mounting base screws (4)
Mounting surface
Cable channel
Camera
Orientation mark
Camera
Mounting base screws (4)
5.
Route extension cables from the power source and LAN switch (or LAN with PoE) into the
electrical box, and then up through the cable opening in the adapter plate.
Step 2.
Connect camera drop cables to LAN and power
1.
Connect the network LAN and power extension cables to the camera drop cables:
Camera
a.
Connect the Ethernet patch cable to the camera network drop cable. Protect the
connection from moisture and other contamination, if necessary. A Waterproof Ethernet
Fitting is provided. Installation instructions for the fitting are included at the end of this
document.
Network drop cable
from camera
!
WARNING
b.
If the camera is not powered using PoE (Power over Ethernet injector), connect the 12 Vdc
power cable to the camera drop cable. The polarity of the drop cable connector is shown
below.
CAUTION
2.
Attach an earth ground wire to the ground terminal on the mounting base, if needed. Follow
local electrical codes when making this connection.
3.
Secure the camera to the mounting surface or Junction box using appropriate screws.
4.
Apply power to the camera through the 12 Vdc power cable or PoE injector, as configured.
Step 3.
Install the Alibi Config Tool software
The Alibi Config Tool is a PC-based network utility for discovery of Alibi compatible devices. It provides
an easy way to activate devices, configure camera and recorder network configuration settings, and set
device passwords. It can be installed on a Microsoft® Windows® operating system that has direct access
to the network where your Alibi devices are installed. You can download the Alibi Configuration Tool
from AlibiSecurity.com/Resources.
1.
Download the Alibi Config Tool from the AlibiSecurity.com/Resources website. At the time
when this document was published, the file is named: alibi-config-tool.zip and is about
79.4MB.
2.
Un-zip the file on a computer with Microsoft Windows (Windows 7 or newer) that is connected
to the LAN where your Alibi camera is connected.
Run the file contained in the zip file: Alibi Config Tool.exe. Follow the on-screen instructions
3.
to install the file.
4.
Open the Alibi Config Tool application. When the application opens, it automatically "discovers"
and lists all Alibi compatible devices on the LAN. See below.
Notice in the screen above, the tool discovered devices with IP addresses of 10.1.10.xxx and
192.168.3.xxx. It will also list other Alibi compatible devices on the LAN, and devices with the
address 192.168.1.64 (an inactive Alibi device).
Camera
Waterproof Ethernet Fitting installed
Failure of the power or Ethernet connector due to moisture or another
contaminant is considered an installation error, which voids the warranty. If
installing this camera in a location such as an overhang, shop, garage, kitchen,
etc. where high humidity or dust is present, seal these connections adequately.
Do not apply power to the camera at this time. Before applying power to the camera, ensure
that the polarity is correct. An incorrect connection may cause a malfunction and can damage
the camera.
© 2019 Observint Technologies. All rights reserved.
Ethernet switch
Network cable from
router or switch