Fujitsu ETERNUS DX Disk Руководство по конфигурации - Страница 8

Просмотреть онлайн или скачать pdf Руководство по конфигурации для Сервер Fujitsu ETERNUS DX Disk. Fujitsu ETERNUS DX Disk 35 страниц. Server connection, fcoe for linux driver settings for converged network adapter cards
Также для Fujitsu ETERNUS DX Disk: Руководство пользователя (35 страниц), Руководство пользователя (42 страниц), Руководство по конфигурации (28 страниц), Руководство по конфигурации (44 страниц), Руководство по конфигурации (28 страниц), Руководство по конфигурации (29 страниц), Руководство по конфигурации (25 страниц), Руководство по конфигурации (32 страниц), Руководство по конфигурации (31 страниц), Руководство по конфигурации (43 страниц), Руководство по конфигурации (21 страниц), Руководство по конфигурации (24 страниц)

Печатать страницу
Fujitsu ETERNUS DX Disk Руководство по конфигурации
Chapter 1
Setup Procedure for Emulex Converged Network Adapter Cards
1.2
Setting Up the Converged Network Adapter Cards
3
Enter the number of the Converged Network Adapter card that is to be checked and press the [Enter]
key.
Example:
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
You Will be prompted to reboot for all changes to take effect.
1. OCe10102-F:
2. OCe10102-F:
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
==> Select 1
4
Check the [Mem Base] and [Port Name] values.
The value of [Mem Base] is the physical address and the value of [Port Name] is the Converged Net-
work Adapter card WWN.
Example:
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
01:
Mem Base:
Port Name:
Vlan ID:
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
===>
5
Record the physical address and WWN in the "WWN instance management table for the server".
Refer to
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (FCoE) for VMware
Emulex OneConnect FCoE BIOS Utility, xxxxxxxx
This utility displays and saves changes when selected.
Emulex Adapter in the System:
Bus:03 Dev:00 Func:02
Bus:03 Dev:00 Func:03
Enter <Esc> to exit
<↑/↓> to Highlight, <Enter> to Select
Copyright (c) 1997-2009 Emulex. All rights reserved.
Emulex OneConnect FCoE BIOS Utility, XB4.01a0
OCe10102-F:
CD4C0000
Firmware Version:
10000000C9D043DD
1002
DCBX mode:
CEE mode
Enable/Disable Boot from SAN
Scan for Target Devices
Reset Adapter Default
Configure Boot Devices
Configure DCBX mode
Configure FCF CEE Parameters
Configure FCF CIN Parameters
Configure Advanced Adapter Parameters
Enter <Esc> to Previous Menu
< / > to Highlight, <Enter> to Select
Copyright (c) 1997-2009 Emulex. All rights reserved.
"Appendix A WWN Instance Management Table for the Server (Blank)" (page
Copyright 2015 FUJITSU LIMITED
WWPN:
10000000C9D043DD
WWPN:
10000000C9D043DF
<PageDn> to Next Page
Bus#: 03 Dev#: 00 Func#: 02
2.702.200.28
BIOS: Disabled!
Node Name:
20000000C9D043DD
8
33).
®
ESX
P3AM-4772-11ENZ0