Aqua One MariSys 240 Руководство - Страница 10

Просмотреть онлайн или скачать pdf Руководство для Системы фильтрации воды Aqua One MariSys 240. Aqua One MariSys 240 15 страниц.
Также для Aqua One MariSys 240: Руководство по быстрой настройке (2 страниц)

Печатать страницу

Maintenance

To ensure optimum filter performance, routine

maintenance should be performed monthly or

less depending on size of tank, amount of fish

and number of daily feeding. If the filter and

media are neglected, the filter media will

become clogged and unable to collect waste

material. This can affect aquarium water quality

and possibly the health of the tank inhabitants.

Grimy waste can also damage the Priming

Pump, Power Head and also diminish the filter

efficiency.

Please Note: It is best to turn the system off

whenever any maintenance is performed on the

MariSys or Overflow Box.

Do not use soap or detergents that can harm

the tank inhabitants.

The Filter Wool should be changed or rinsed

every two to three weeks or as needed. The

Activated Carbon Pad should be replaced

monthly when there is a normal bio-load.

Replacing Filter Media

1. Remove the Media Access Lid and Drip Tray.

2. Remove the Media Basket containing the

Filter Wool and Carbon Pad. Hold the Media

Access Lid under the Media Basket to keep the

water from splashing on the floor while

transporting it to the sink.

Ensure there is not soap or other residue

around the sink area.

3. Take the Media Basket to the sink and

remove all of the Filter Wool Pads and the

Carbon Pad.

4. Rinse the Media Baskets under cool running

water.

5. Place the new Carbon Pad at the bottom of

the Media Basket followed by the rinsed or new

Wool Pads.

6. Replace the Carbon Pillow every four weeks

or less, depending on number of aquatic

animals, discoloration or cloudy water and the

amount of daily feeding.

7. The Bio Balls and CeramiSub should not be

washed under tap water at any stage. They can

be dunked in a bucket of aquarium water if they

are extremely dirty. Replace 1/3rd of the

CeramiSub every 12 months as the media can

clog and stop working effectively.

Consult your Aqua One specialist for further

advice on maintaining your biological media.

Power Head Maintenance

The Power Head should be disassembled and

cleaned on a monthly basis. Refer to the

Diagram on page 11 for the following

instructions.

1. Turn off all power and unplug the Power

Head before servicing the unit.

2. Remove the Media Access Lid.

3. Take hold of the Power Head / Protein

Skimmer Housing and pull gently upward to

expose the Power Head for servicing.

4. Hold the Power Head and remove the Inlet

Elbow.

5. Gently turn the Impeller Cover Lock

anti-clock wise to remove it.

6. Pull the Impeller Cover away from the Motor.

This will be a tight fit.

5. Clasp the Impeller Blades with needle nose

pliers and slowly pull the Impeller from the

Impeller Well.

6. Clean Impeller under warm running water.

Do not use soap or detergent. Remove the

Rubber End Caps and Ceramic Shaft and run

clean water through the hole in the center of the

Impeller.

7. Use an Aqua One Double Ended Pipe Brush

to clean the Impeller Well thoroughly. (Where

the impeller sits in the Motor)

8. Reassemble in the reverse order, ensure an

aquarium safe lubricant is used to lubricate the

O-ring on the Impeller Cover.

Priming Pump Maintenance

1. Flush the Priming Pump whenever the Power

Head is maintained.

2. Disconnect the Pump from the V - Joint on

top of the Water Bridge, leave the Air line

attached to the Pump.

3. Fill a small container with clean fresh tap

water.

4. Set the Pump up so that both of the air line

ends are in the water.

5. Turn the Pump on and allow it to circulate

with for around 10 minute.

6. After 10 Minutes switch the Pump off and

reconnect it to the system.