Aqua One MariSys 240 Manuel - Sayfa 10
Su Filtrasyon Sistemleri Aqua One MariSys 240 için çevrimiçi göz atın veya pdf Manuel indirin. Aqua One MariSys 240 15 sayfaları.
Ayrıca Aqua One MariSys 240 için: Hızlı Kurulum Kılavuzu (2 sayfalar)
Maintenance
To ensure optimum filter performance, routine
maintenance should be performed monthly or
less depending on size of tank, amount of fish
and number of daily feeding. If the filter and
media are neglected, the filter media will
become clogged and unable to collect waste
material. This can affect aquarium water quality
and possibly the health of the tank inhabitants.
Grimy waste can also damage the Priming
Pump, Power Head and also diminish the filter
efficiency.
Please Note: It is best to turn the system off
whenever any maintenance is performed on the
MariSys or Overflow Box.
Do not use soap or detergents that can harm
the tank inhabitants.
The Filter Wool should be changed or rinsed
every two to three weeks or as needed. The
Activated Carbon Pad should be replaced
monthly when there is a normal bio-load.
Replacing Filter Media
1. Remove the Media Access Lid and Drip Tray.
2. Remove the Media Basket containing the
Filter Wool and Carbon Pad. Hold the Media
Access Lid under the Media Basket to keep the
water from splashing on the floor while
transporting it to the sink.
Ensure there is not soap or other residue
around the sink area.
3. Take the Media Basket to the sink and
remove all of the Filter Wool Pads and the
Carbon Pad.
4. Rinse the Media Baskets under cool running
water.
5. Place the new Carbon Pad at the bottom of
the Media Basket followed by the rinsed or new
Wool Pads.
6. Replace the Carbon Pillow every four weeks
or less, depending on number of aquatic
animals, discoloration or cloudy water and the
amount of daily feeding.
7. The Bio Balls and CeramiSub should not be
washed under tap water at any stage. They can
be dunked in a bucket of aquarium water if they
are extremely dirty. Replace 1/3rd of the
CeramiSub every 12 months as the media can
clog and stop working effectively.
Consult your Aqua One specialist for further
advice on maintaining your biological media.
Power Head Maintenance
The Power Head should be disassembled and
cleaned on a monthly basis. Refer to the
Diagram on page 11 for the following
instructions.
1. Turn off all power and unplug the Power
Head before servicing the unit.
2. Remove the Media Access Lid.
3. Take hold of the Power Head / Protein
Skimmer Housing and pull gently upward to
expose the Power Head for servicing.
4. Hold the Power Head and remove the Inlet
Elbow.
5. Gently turn the Impeller Cover Lock
anti-clock wise to remove it.
6. Pull the Impeller Cover away from the Motor.
This will be a tight fit.
5. Clasp the Impeller Blades with needle nose
pliers and slowly pull the Impeller from the
Impeller Well.
6. Clean Impeller under warm running water.
Do not use soap or detergent. Remove the
Rubber End Caps and Ceramic Shaft and run
clean water through the hole in the center of the
Impeller.
7. Use an Aqua One Double Ended Pipe Brush
to clean the Impeller Well thoroughly. (Where
the impeller sits in the Motor)
8. Reassemble in the reverse order, ensure an
aquarium safe lubricant is used to lubricate the
O-ring on the Impeller Cover.
Priming Pump Maintenance
1. Flush the Priming Pump whenever the Power
Head is maintained.
2. Disconnect the Pump from the V - Joint on
top of the Water Bridge, leave the Air line
attached to the Pump.
3. Fill a small container with clean fresh tap
water.
4. Set the Pump up so that both of the air line
ends are in the water.
5. Turn the Pump on and allow it to circulate
with for around 10 minute.
6. After 10 Minutes switch the Pump off and
reconnect it to the system.
10