Dell PowerEdge M820 Systems Информация о выпуске - Страница 13

Просмотреть онлайн или скачать pdf Информация о выпуске для Переключатель Dell PowerEdge M820 Systems. Dell PowerEdge M820 Systems 27 страниц. Dell poweredge blade servers getting started guide
Также для Dell PowerEdge M820 Systems: Обновление информации (38 страниц), Руководство пользователя (23 страниц), Важная информация Руководство (35 страниц), Руководство по обновлению (32 страниц), Руководство по обновлению (28 страниц), Руководство пользователя (26 страниц), Руководство пользователя (22 страниц), Руководство по началу работы (12 страниц), Руководство пользователя (3 страниц), Техническое руководство (46 страниц), Руководство по портфолио (27 страниц), Руководство по началу работы (14 страниц), Руководство по началу работы (12 страниц), Техническое руководство (47 страниц)

Печатать страницу
Dell PowerEdge M820 Systems Информация о выпуске
PowerConnect M6220/M6348/8024/8024F/M8024/M8024-k/
7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes
 LACP Ports Inactive Until Attached
Ports in a LAG configured to use LACP (dynamic LAG) remain inactive (discard received traffic) until they become
attached to the LAG. LACP ports that are attached to a LAG will enter the discarding state if they become detached
from the LAG for any reason.
Port level configuration for a port that is configured in a dynamic LAG is disregarded. Remove the port from the LAG
to restore use of the port level configuration.
Ports in a static LAG begin forwarding on link up. Ports in a static LAG disregard port level configuration. Configure
static LAG functions on the static LAG interface.
NOTE:
It is recommended that administrators disable portfast and auto-
portfast on physical interfaces configured in a LAG. Portfast and auto-
portfast can interfere with an interface entering into LAG mode on a
reboot and possibly enable a packet storm.
 Spanning Tree Changes
Administrators may assign more than 1024 VLANs to MSTP instances. Only VLANs that are configured on the switch
will forward traffic.
The PowerConnect switches implements the 802.1Q-2005 standard which builds on 802.1D-2004. 802.1D-2004
incorporates the the 802.1t, 802.1w and 802.1s revisions. Port path costs are calculated based on the interface speed as
shown below and are dynamically recalculated on interface activation and link speed changes.
External Port Path Cost values (Port Path Cost in 17.14 of 802.1D-2004) are applicable in STP, RSTP, and MST modes
(Ref. Table 17-3 802.1D-2004). Use the spanning-tree cost command in interface mode to set the external port path
cost.
Link Speed
10 Gb/s
1 Gb/s
100 Mb/s
10 Mb/s
1 Mb/s
Internal Port Path Cost values are specific to MST mode only (Ref. Table 13-3 802.1Q-2005). Use the spanning-tree
mst <instance> cost command in interface mode to set the internal port path cost.
Link Speed
10 Gb/s
1 Gb/s
100 Mb/s
10 Mb/s
1 Mb/s
System Firmware Version 4.1.0.6
Default Value
2000
20000
200000
2000000
20000000
Default Value
2000
20000
200000
2000000
20000000
Page 11