Dell PowerEdge M820 Systems Sürüm Notları - Sayfa 13

Anahtar Dell PowerEdge M820 Systems için çevrimiçi göz atın veya pdf Sürüm Notları indirin. Dell PowerEdge M820 Systems 27 sayfaları. Dell poweredge blade servers getting started guide
Ayrıca Dell PowerEdge M820 Systems için: Bilgi Güncellemesi (38 sayfalar), Kullanıcı Kılavuzu (23 sayfalar), Önemli Bilgiler Kılavuzu (35 sayfalar), Güncelleme Kılavuzu (32 sayfalar), Güncelleme Kılavuzu (28 sayfalar), Kullanıcı Kılavuzu (26 sayfalar), Kullanıcı Kılavuzu (22 sayfalar), Başlangıç Kılavuzu (12 sayfalar), Kullanıcı El Kitabı (3 sayfalar), Teknik Kılavuz (46 sayfalar), Portföy Kılavuzu (27 sayfalar), Başlangıç Kılavuzu (14 sayfalar), Başlangıç Kılavuzu (12 sayfalar), Teknik Kılavuz (47 sayfalar)

Sayfayı Yazdır

Dell PowerEdge M820 Systems Sürüm Notları

PowerConnect M6220/M6348/8024/8024F/M8024/M8024-k/

7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes

 LACP Ports Inactive Until Attached

Ports in a LAG configured to use LACP (dynamic LAG) remain inactive (discard received traffic) until they become

attached to the LAG. LACP ports that are attached to a LAG will enter the discarding state if they become detached

from the LAG for any reason.

Port level configuration for a port that is configured in a dynamic LAG is disregarded. Remove the port from the LAG

to restore use of the port level configuration.

Ports in a static LAG begin forwarding on link up. Ports in a static LAG disregard port level configuration. Configure

static LAG functions on the static LAG interface.

NOTE:

It is recommended that administrators disable portfast and auto-

portfast on physical interfaces configured in a LAG. Portfast and auto-

portfast can interfere with an interface entering into LAG mode on a

reboot and possibly enable a packet storm.

 Spanning Tree Changes

Administrators may assign more than 1024 VLANs to MSTP instances. Only VLANs that are configured on the switch

will forward traffic.

The PowerConnect switches implements the 802.1Q-2005 standard which builds on 802.1D-2004. 802.1D-2004

incorporates the the 802.1t, 802.1w and 802.1s revisions. Port path costs are calculated based on the interface speed as

shown below and are dynamically recalculated on interface activation and link speed changes.

External Port Path Cost values (Port Path Cost in 17.14 of 802.1D-2004) are applicable in STP, RSTP, and MST modes

(Ref. Table 17-3 802.1D-2004). Use the spanning-tree cost command in interface mode to set the external port path

cost.

Link Speed

10 Gb/s

1 Gb/s

100 Mb/s

10 Mb/s

1 Mb/s

Internal Port Path Cost values are specific to MST mode only (Ref. Table 13-3 802.1Q-2005). Use the spanning-tree

mst <instance> cost command in interface mode to set the internal port path cost.

Link Speed

10 Gb/s

1 Gb/s

100 Mb/s

10 Mb/s

1 Mb/s

System Firmware Version 4.1.0.6

Default Value

2000

20000

200000

2000000

20000000