Aquatec OCEAN VIP Commode Руководство по эксплуатации - Страница 7
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Инвалидное кресло Aquatec OCEAN VIP Commode. Aquatec OCEAN VIP Commode 10 страниц. Commode
Печатать страницу
6
Operation
6.1
Adjusting the seat height
Important!
●
The seat height must be adjusted to suit the
user. As a rule, the seat height is correctly
adjusted when the user is sitting on the
commode and both feet touch the ground.
●
The seat height must be adjusted on both
sides simultaneously. To make adjust-
ments, a second person is required to help.
●
Do not adjust the seat height of the com-
mode when someone is sitting on it.
1.
Slightly raise the commode at the seat frame.
2.
Take out both clips (5, fig. 8).
3.
To adjust the seat height, pull the seat frame out
of the side section (1, fig. 8) or push it in.
4.
Align the clip recesses (3, fig. 8) at the side sec-
tion with a hole on the seat frame (4, fig. 8).
5.
Push both clips from the outside into the side sec-
tion until the two lugs (6, fig. 8) enclose the seat
frame tube (2, fig. 8).
6.2
Adjusting the height of the footrests
1.
Pull up the footrest (1, fig. 6) slightly.
2.
Pull out the clip (7, fig. 6) and put it in again at the
required position. Pull out the footrest slightly fur-
ther if necessary.
3.
Push down the footrest until the groove (2, fig. 6)
catches the pin of the clip (7, fig. 6).
4.
Set the other footrest to the same height as de-
scribed.
6.3
Adjusting the inclination of the foot
plates
Important!
●
The inclination of the foot plates can be ad-
justed infinitely variably.
●
The right and left foot plates must be ad-
justed in the same way.
1.
Loosen the Allen screw (3, fig. 6) on the foot plate
using a size 4 Allen key.
2.
Turn the foot plate (4, fig. 6) to the desired posi-
tion.
3.
Tighten the Allen screw again.
EN
6.4
Adjusting the height of the armrests
Important!
●
The height of the armrests must be adjust-
ed to suit the user.
●
The height of the armrests must be adjust-
ed by the same amount on both sides.
●
The height of the right and left armrest is
adjusted in the same way.
1.
Open the belt lock of the belt inside the backrest
frame at the backrest cover.
2.
Open the belt lock of the belt above the armrests
at the backrest cover (1, fig. 9).
3.
Feed this belt along the backrest frame and close
again.
Important!
The nuts are inserted loosely in the fastening
clamp and can fall out.
4.
Unscrew the screws (3, fig. 9) of the armrest hold-
er (4, fig. 9) using the supplied Allen key.
5.
Remove the fastening clamp (2, fig. 9) with the
nuts from the inside of the backrest frame.
6.
Remove the armrest holder (4, fig. 9) with the
armrest and move upwards.
Important!
The small hole is for fixing the fastening clamp.
7.
Insert the screws into the armrest holder and
guide into the holes in the backrest frame.
8.
Replace the nuts in the fastening clamp if neces-
sary.
9.
Place the fastening clamp onto the backrest frame
so that the fixing of the fastening clamp engages
with the small hole.
10. Insert the screws into the nuts and tighten.
11. Guide the belt of the backrest cover around the
back rest frame, close it and then tighten all the
belts.
Follow the same procedure to adjust the armrests to
the lower position.
Important!
Open the belt below the armrest and feed it
through the backrest frame if you are adjusting
the armrest to the lower position.
13