HP ProCurve 1600M Руководство по установке - Страница 20

Просмотреть онлайн или скачать pdf Руководство по установке для Переключатель HP ProCurve 1600M. HP ProCurve 1600M 28 страниц. Redundant power supply
Также для HP ProCurve 1600M: Технический паспорт (12 страниц), Прочитай меня сначала (8 страниц), Руководство рецензента (27 страниц), Дополнительное руководство (2 страниц), Дополнительное руководство (2 страниц), Руководство по установке (36 страниц), Руководство по установке (28 страниц), Руководство по быстрой настройке (2 страниц), Руководство по быстрой настройке (4 страниц), Руководство пользователя (8 страниц), Дополнение к руководству (28 страниц), Прочитай меня сначала (16 страниц), Установка и удаление (2 страниц), Руководство по установке (12 страниц), Руководство по планированию и реализации (40 страниц), Инструкции по разборке изделия в конце срока службы (2 страниц), Руководство по установке (46 страниц), Руководство по диагностике (2 страниц), Инструкции по разборке (2 страниц)

HP ProCurve 1600M Руководство по установке
Troubleshooting
Tip
Number
Problem
–
The module installed in
the slot has
experienced a self test
or initialization fault.
—
The module installed in
the slot that
corresponds to the
letter that is flashing
has experienced a
downloading fault.
˜
A module was installed
in the slot that is a
different type than the
previously installed
module, and the switch
has not yet been reset.
14
The module is tested whenever the switch is powered on, or reset (through the
Reset button on the switch, or the Reboot or Reset options in the console or web
browser interface), and when it is hot swapped (installed when the switch is
powered on).
Try reinstalling the module. You can do this without having to power down the
switch. When the module is reinstalled, it will be retested automatically. Make
sure to screw in the retaining screws so that the module cannot be inadvertently
pulled out by pulling on the network cables.
If the fault indication reoccurs, the module may have failed. Remove the module
from the switch and replace it with another module, or recover the slot with the
cover plate. Call your HP-authorized LAN dealer, or use the electronic support
services from HP to get assistance. See the Customer Support/Warranty booklet
for more information.
Operating code and configuration information is downloaded to each switch
module whenever the switch is powered on, or reset (through the Reset button
on the switch, or the Reboot or Reset options in the console or web browser
interface), and when they are hot swapped (installed when the switch is
powered on). In this fault condition, an error has occurred in the download
process.
Try reinstalling the module. You can do this without having to power down the
switch. When the module is reinstalled, it will be retested automatically.
If the fault indication reoccurs, the module may have failed. Remove the module
from the switch and replace it with another module, or recover the slot with the
cover plate. Call your HP-authorized LAN dealer, or use the electronic support
services from HP to get assistance. See the Customer Support/Warranty card
for more information.
When you "hot swap" modules in the switch slot, if you install a different module
type than the one that was previously installed in the slot, you must reset the
switch so the switch processor can properly initialize and configure the new
module type. The flashing LED informs you that this change of module types has
occurred. The module will not work properly until the switch is reset as indicated
by all the module's LEDs staying on until the switch is reset.
See "Resetting the Switch" on page 12.
Solution