DieHard Portable Power 1150 Руководство по эксплуатации - Страница 10
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Дистанционное пусковое устройство DieHard Portable Power 1150. DieHard Portable Power 1150 12 страниц. Diehard portable power 1150 battery charger operator's manual
Также для DieHard Portable Power 1150: Руководство пользователя (11 страниц), Руководство по эксплуатации (16 страниц), Руководство по эксплуатации (15 страниц), Руководство по эксплуатации (17 страниц)
Печатать страницу
8.11
Powering a 120v AC Device
To operate a 120V AC device:
1.
Ensure that the battery clips are securely on the storage holders.
2.
Open the protective cover of the AC power outlet on the front panel of the jump starter.
3.
Make sure the 120V AC device to be operated is turned OFF.
4.
Plug the 120V AC device into the AC power outlet, and turn the Inverter/Compressor
Switch to the INVERTER position.
5.
Turn the device on.
6.
If the device does not operate properly when first connected to the inverter, push the
inverter rocker switch ON, OFF, and ON again in quick succession. If this procedure
is not successful, it is likely that the inverter does not have the required capacity to
operate the device intended.
7.
Charge the jump starter as soon as possible after each use.
Risk of electric shock.
Incorrect operation of your inverter may result in damage and personal injury.
The inverter output is 120V AC and can shock or electrocute the same as any
ordinary household AC wall outlet.
120v AC Electrical Device Example Run-Time Chart
Appliance Type
Spotlights, Sump Pumps, DVD Players
Faxes, TVs, Small Power Tools
Computer Printer, Medium Power
Tools, Blenders
NOTE: These are estimated run-times, actual time may vary. Times are based on the
internal battery being new, fully charged and operated at room temperature.
NOTE: The maximum continuous load is 400 watts. Do not use the inverter with a
product that draws more than 400 watts, as this may cause damage to the inverter
and the product.
9.
MAINTENANCE INSTRUCTIONS
9.1
After use and before performing maintenance, unplug and disconnect the jump starter
(see sections 3 and 4).
9.2
Use a dry cloth to wipe all battery corrosion and other dirt or oil from the battery clips,
cords and the jump starter case.
9.3
Ensure that all of the jump starter components are in place and in good working
condition, for example, the plastic boots on the battery clips.
9.4
Servicing does not require opening the unit, as there are no user-serviceable parts.
9.5
All other servicing should be performed by qualified service personal.
10.
MOvING AND STORAGE INSTRUCTIONS
10.1
Store the jump starter in an upright position.
10.2
Store inside, in a cool, dry place.
10.3
Do not store the clips on the handle, clipped together, on or around metal, or clipped to
cables. The clips on the jump starter are live and will produce arcing or sparking if they
come in contact with each other. To prevent accidental arcing, always keep the clips on
the storage holders when not using them to jump start a vehicle.
10.4
If the jump starter is moved around the shop or transported to another location, take
care to avoid/prevent damage to the cords, clips and jump starter. Failure to do so could
result in personal injury or property damage.
where damage could occur if the internal battery should unexpectedly leak acid.
Do not use and/or store the jump starter in or on any area or surface
Estimated Power
100 Watts
150 Watts
200 Watts
9
•
•
Estimated Time*
1.5 Hours
1.25 Hours
55 Minutes