Axxess AX-TYAMP1-SWC Руководство по установке - Страница 5
Просмотреть онлайн или скачать pdf Руководство по установке для Усилитель Axxess AX-TYAMP1-SWC. Axxess AX-TYAMP1-SWC 8 страниц. Lexus/toyota amp interface with swc 2002-2015
Печатать страницуL.E.D. feedback
The (16) Red L.E.D. flashes represent what brand radio the AX-TYAMP1-SWC believes it
is connected to. Each flash represents a different radio manufacturer. For example, if you
are installing a JVC radio, the AX-TYAMP1-SWC will flash Red (5) times, and then stop.
Following is a legend that dictates which radio manufacturer corresponds to which flash .
L.E.D. feedback legend
1 flash - Eclipse (Type 1) †
2 flashes - Kenwood ‡
3 flashes - Clarion (Type 1) †
4 flashes - Sony/Dual
5 flashes - JVC
6 flashes - Pioneer/Jensen
7 flashes - Alpine *
8 flashes - Visteon
* Note: If the AX-TYAMP1-SWC flashes Red (7) times, and you do not have an Alpine radio
connected to it, that means the AX-TYAMP1-SWC does not detect a radio connected it. Verify
that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio.
** Note: The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must
be updated to rev. 2.1.4.
† Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio
type to the other Clarion radio type; same for Eclipse. The following section explains how to do this.
‡ Note: If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC
radio, change the radio type to a Kenwood. The following section explains how to do this.
Steering wheel control extra settings
9 flashes - Valor
10 flashes - Clarion (Type 2) †
11 flashes - Metra OE
12 flashes - Eclipse (Type 2) †
13 flashes - LG
14 flashes - Parrot **
15 flashes - XITE
16 flashes - Philips
®
AX-TYAMP1-SWC
Attention:
The Axxess Updater App can also be used to program the following (3)
sub-sections as well, pending that the interface has been initialized and programmed.
Changing radio type
If the L.E.D. flashes do not match the radio you have connected, you must
manually program the AX-TYAMP1-SWC to tell it what radio it is connected to.
1. After (3) seconds of turning the key on, press and hold the Volume-Down button
on the steering wheel until the L.E.D. in the AX-TYAMP1-SWC goes solid.
2. Release the Volume-Down button; the L.E.D. will go out indicating we are now
in Changing Radio Type mode.
3. Refer to the Radio Legend to know which radio number you would like to have
programmed.
4. Press and hold the Volume-Up button until the L.E.D. goes solid, and then
release. Repeat this step for the desired radio number you have selected.
5. Once the desired radio number has been selected, press and hold the Volume-
Down button on the steering wheel until the L.E.D. goes solid. The L.E.D. will
remain on for about (3) seconds while it stores the new radio information.
6. Once the L.E.D. goes off, the Changing Radio Type mode will then end. You can
now test the steering control wheel controls.
Note: If at any time the user fails to press any button for a period longer than
(10) seconds, this process will abort.
Continued on the next page