Epson ActionLaser II Информация о продукте - Страница 8
Просмотреть онлайн или скачать pdf Информация о продукте для Принтер Epson ActionLaser II. Epson ActionLaser II 12 страниц. Epson actionlaser actionlaser ii: product information
Также для Epson ActionLaser II: Бюллетень поддержки продуктов (2 страниц)
Печатать страницуActionLaser II
[E] INSUFF MEMORY
The printer has insufficient memory available for the task you
it. To correct
have given
the
remains, press RESET or perform INITIALIZE. This error can also
be cleared by turning the printer off and back on again. However,
it may be necessary to simplify the page you are trying to print or
add more memory to the printer.
[E] PAGE BUFFER FULL
Text or graphics data has filled the printer's buffer and an
incomplete page is ejected. Press
may need to add more memory to
[S] PAPER FEEDING
The printer is feeding paper.
[E] PAPER JAM
Paper is
being fed into the printer or paper is jammed inside
not
the paper path. See the PAPER JAM section later in this chapter.
[E] PAPER OUT
There is no paper in the standard paper cassette or the optional
multi-media feeder (if installed). Insert more paper into the
selected paper cassette or manually feed a sheet of paper into the
printer.
[E] PAPER OUT [paper source][paper size]
There is
no
paper in the paper source from which the printer
expects to feed paper. The right column of the display prompts
you to load the correct paper size into the paper source.
[E] PAPER SIZE ERROR
The paper size you selected with SelecType (or the default size if
you have not
selected
a
size) does
the selected paper
source.
Press
the correct paper
or change
application software or with SelecType.
[S] PRINTING
The printer has received data and is printing.
[S] PRINT STOP
The printer stops printing during a multi-copy print operation.
[S] RAM Check X.X MB
The printer is checking RAM (X.X = capacity).
IS] READY
The printer is ready to print.
[E] REINSERT CARD
If this message appears on the display, you may have
identity card or a font cartridge while the
while
the
printer was on line. To correct the error, make sure the
printer is off line. Next, reinsert the card or cartridge and press
CONTINUE.
[E] REMOVE CARD
You may have inserted an identity card or a font cartridge while
the printer was on line or while
error, take the printer off line, then remove the card or
this
cartridge and press
CONTINUE.
cartridge, make sure that all data in the buffer has been printed
and that the printer is off
line. If the FEED light is on,
print out the remaining data.
ALll-8
error, press
If
CONTINUE.
the message
to clear
error. You
CONTINUE
the
the
printer.
not match
the paper loaded in
CONTINUE
to clear
the
error. Insert
the P-SIZE setting
with your
removed an
FEED
light was still lit or
light was on. To correct
the FEED
Before reinserting
card or
the
press
FEED
[E] RESELECT TRAY
optional
The
multi-media
option is set to OPT or AUTO. Install the optional multi-media
feeder and
press
then
use the optional multi-media feeder, simply press
paper is automatically selected from the standard paper cassette.
[S] RESET
The printer has been reset to previous settings to the macro
number specified with the LOAD MACRO setting in
CONFIG option of SelecType Level 1.
[S] ROM Check
The printer is checking ROM.
[E] SAVE MEMORY OVERFLOW
This message may appear
with the SYSTEM CONFIG option SAVE MACRO setting in
SelecType Level 1. The printer does
save any additional macros. To correct this error, delete unused
macros using the DELETE MACRO setting, and then repeat
SAVE MACRO.
[E] SERVICE REQ. CXXX
[E] SERVICE REQ. E00XX
A controller or print engine error has been detected. Write down
the error number
and turn off the printer. Turn the printer back on after a few
see if the error message still appears. If it does, turn off
seconds to
the printer, unplug the power cord from the electrical outlet, and
contact a qualified service person.
[E] SET [paper size] MANUAL
This message requires that you set the paper size for manual
feeding.
[E] STARTUP ERROR
Press a to continue.
[E] SET FULL PRINT
This message may appear
or
mix of
a
text and
FULL PRINT setting in SelecType Level 1. See Chapter 4 for more
information about this setting.
[S] STANDBY MODE
If the standby mode is enabled, the printer enters this mode when
it is not used for about thirty minutes. This
Press any control panel button or send data to the printer to
warm it up. It will also enter this mode after 8
mode is disabled.
[W] TONER LOW
The printer is almost out of toner. When you see this message,
you can still print up to 20 more pages. Then you must replace the
toner cartridge.
[E] TONER OUT
The toner cartridge must be replaced.
[E] TRAY SET XXX
The paper-size setting does not match the paper loaded in the
specified paper cassette. The right column of
to
the currently selected cassette and
can either change the paper-size setting or load the correct paper
size. After you correct the paper mismatch, press
[S] WARMING UP
The printer is warming up.
9/17/91
feeder is not installed and the INPUT
However, if you decide not to
CONTINUE.
are trying to save a
when you
enough memory to
not have
that
appears in the right column of the display
are trying to print graphics
when you
graphics. Press
and then
CONTINUE
message
hours even
the
the
expected paper size. You
and
CONTINUE
SYSTEM
the
macro
change the
appears.
if the
display indicates
CONTINUE.
Laser Printers