Siemens SINAMICS G120 Руководство по быстрой установке

Просмотреть онлайн или скачать pdf Руководство по быстрой установке для Промышленное оборудование Siemens SINAMICS G120. Siemens SINAMICS G120 2 страницы. Using blocksize converters in marine applications
Также для Siemens SINAMICS G120: Начало работы (46 страниц), Руководство по эксплуатации (32 страниц), Начало работы (30 страниц), Инструкции по установке оборудования (2 страниц), Инструкции по установке и руководство пользователя (2 страниц), Инструкции по установке (2 страниц), Инструкции по установке (2 страниц), Компактная инструкция по эксплуатации (32 страниц), Руководство (42 страниц), Начало работы (50 страниц), Руководство по эксплуатации устройства (34 страниц), Описание приложения (50 страниц), Компактная инструкция по эксплуатации (2 страниц), Руководство (31 страниц), Руководство по применению (34 страниц), Компактная инструкция по эксплуатации (2 страниц), Компактная инструкция по эксплуатации (2 страниц)

Печатать страницу

SINAMICS

SINAMICS CONNECT

Quick Install Guide

Mounting

Before mounting and commissioning

1.1

IMPORTANT: observe all documents enclosed with the device and the

SINAMICS CONNECT Operating Instructions before mounting and

connecting the device.

Note that the term "device" refers to a SINAMICS CONNECT unit.

The symbol indicates that you can refer to the Operating

Instructions manual for more information.

1.2

Scope of delivery

Check the scope of delivery for completeness and intactness:

• One SINAMICS CONNECT device with one DC terminal block

mounted

• Quick Install Guide in English

1.3

Valid mounting orientation

50 °C

Horizontal

0 °C

When the device is used in the area of Industrial Control Equipment in

accordance with UL 61010-2-201, note that the device is classified as

"Open Type". A UL 61010-2-201 conform enclosure is therefore a

mandatory requirement for approval or operation according to UL

61010-2-201.

Free space required around the device

≥ 50 mm

A5E45421417-002

10/2018

50 °C

Vertical

0 °C

≥ 50 mm

1.4

Mounting

Mounting on DIN rails

1. Push the device down.

2. Swing the device from below.

3. Push the device to the rail.

Wall mounting

1. Guide a push-in lug

through the opening.

2. Press the push-in lug

down.

3. Drill the holes in the wall

and fasten the device to

the wall with screws and

anchors.

Commissioning

2.1

Connecting the power supply

The device must only be connected to a 9 V DC to 36 V DC power

supply which meets the requirements of safe extra low voltage (SELV)

according to IEC/EN/DIN EN/UL 60950-1.

The power supply must meet the requirements of NEC Class 2 or LPS

according to IEC/EN/DIN EN/UL 60950-1.

If there are voltage peaks on power supply lines, use a protective device

in the form of a varistor (MOV) UMOV = U-rated × 1.2 (BLITZDUCTOR

BVT AVD 24 (918 422) or compatible).

Power

9 V D

Off

t o 3 6

V D C

P o w e

S u p p

l y

–

Click