Siemens DTF4301 Инструкции по установке и эксплуатации

Просмотреть онлайн или скачать pdf Инструкции по установке и эксплуатации для Посудомоечная машина Siemens DTF4301. Siemens DTF4301 2 страницы.

Печатать страницу

Brief and handy:

everything your dishwasher

needs.

Before using for the first

time, read the installation

and operating instructions!

Fill with salt

Fill with rinse aid

Fill with detergent

Turn on the tap

Water ready

Switch on the appliance

Close the door. Press the On/Off switch,

the last selected programme starts automatically.

Select programme

Off we go

Switch off the appliance

When the "programme end" display illumi-

nates, switch off the main switch. Turn off

the tap.

Setting the water softening system *

Find out the water

hardness at your water

utility company and

enter below

* only before using the

dishwasher for the first

time or if the water hard-

ness changes

Dissolves limescale (not required for set value 0!)

Unscrew

the lid.

Everything is sparkling clean ...

Press mark 1,

lift up lid 2.

Very dirty dishes, a lot of detergent ...

If required, open

the lid (press the

pin).

Quick, economical or intensive ...

Overview of programmes

This overview indicates the max. possible number of

programmes. The programmes which correspond to your

appliance can be found on your appliance fascia.

The programme data are values measured in the

laboratory in compliance with Standard EN 50242.

Deviations is practice are possible.

Programme progress / Rinsing noises

Example: Eco programme

Everything o.k.

Start

Read off the setting

°fH

°dH

°Clarke mmol/l

Setting

0–6

0–11

0–8

0–1,1

7–16

12–29

9–20

1,2–2,9

17–21

30–37

21–26

3,0–3,7

22–35

38–60

27–44

3,8–6,2

Only before using

the dishwasher

for the first time

pour approx. 1 l /

2 pt water into the

salt opening.

Warning,

combination

products are not

suitable for all

programmes,

follow manufac-

turer's instructions.

Duration in minutes

Power consumption in kWh

Water consumption in litres

Cleaning / Final rinse

Alternating rinsing and pumping noises

After the drying cycle, water is pumped out for approx. 60 sec. The programme has not ended until the end display

Quickly sorted

and then select a setting

– Hold down programme button B and switch on the main

switch, then release the buttons. The

buttons A and B illuminate (water hardness setting was set

Reset

to 2 at the factory).

– Each time button B is depressed, the setting increases by

one (0-3). If buttons A, B and C illuminate, the maximum

water hardness setting has been reached. If the water

hardness setting is now increased again, the lights go out

and the water hardness setting is set to 0.

– Switch off the main switch. The selected setting has been

stored in the appliance.

Pour in max.

1.5 kg / 3 lb 5 oz

salt (never deter-

gent!)

Refill whenever level indicator is light!

Pour in

rinse aid.

Pour in

detergent.

Normal

Eco

Intensive

70_

65_

50_

103

140

155

1,40

1,35

0,80

No rinsing noises

. display flashes and

Screw on the

lid. Switch on

dishwasher

immediately.

Close the

lid. CLICK!

Push the lid

shut, press.

PLOP!

Quick

Prerinse

Gentle

40_

35_

0,70

0,50

0,10

Dry

15–35 min

End display

lights up